3. MUTE:
Press the MUTE button to temporarily switch off the
sound to the speakers and headphones. Mute mode
is indicated by “MUTING” flashing in red in the dis-
play area. Press
MUTE again to restore sound. Mute
does not affect recordings made using the Tape out-
puts but will affect the signal going to the Audio Pre-
outs.
NOTE:
When the unit is in mute mode, any adjustment of
the VOLUME CONTROL on the front panel (No.9)
will release the muting, i.e. the original volume level
will be resumed.
4. MASTER VOLUME
Master Volume 3 or 4 respectively increases or
decreases the volume setting for all speakers. The
display panel will indicate the level set. The Volume
control does not affect recordings made using the
Tape and Video, or Tape, Video 3 and Video 4 out-
puts but will affect the signal going to the Pre-amp
output (Audio Pre Out).
5. CURSOR 3 , 4 , 1 AND 2 AND ENTER
The four Cursor buttons are used to navigate the
cursor when using the menus with the On Screen
Display and the
ENTER is used to confirm the choice.
Press 3 to move cursor up, 4 to move cursor down, 1
to move cursor left, 2 to move cursor right. Then
press
ENTER to access.
With the four cursor buttons the relative volume
level trims for center, left and right surround channels
can be adjusted. Press the
CHANNEL button (No. 7)
to select the channel for which you wish to adjust the
level.
Refer also to chapter “On Screen Display” and
“Setting Up the Surround Sound System” for more
information.
6. TEST
Pressing the TEST button, engages the Test signal
generator to allow for adjustment of all speaker lev-
els, so that each channel can be adjusted for equal
loudness at your listening position. The test signal
scrolls automatically with 5-second intervals from
Front Left, Center, Front Right, Rear Right, Rear Left,
to subwoofer in continuous cycles. If an adjustment in
setting is made for one of the speakers, scrolling will
stop until 5 seconds after the adjustment was made.
Both display panel and OSD show which speaker is
being fed with the test signal. Use the cursor 1 and 2
button to respectively decrease or increase the level
for the current speaker. Press the TEST button again
to leave or cancel the Test mode, any changes will be
memorized automatically.
Refer also to chapter “On Screen Display” and
“Setting Up the Surround Sound System” for more
information.
7. CHANNEL SELECT
Although the T 760 is correctly set-up it may some-
times be desirable to make minor adjustments to suit
particular software. Pressing the CHANNEL button
allows for direct adjustment of Center, Rear and
Subwoofer levels. Press the
CHANNEL button to
scroll to the next speaker. Both display panel and
OSD show which speaker can be adjusted. Use the
cursor 1 and 2 button to respectively decrease or
increase the level for the current speaker.
Pressing the
CHANNEL button also gives access
to
CHANNEL BALANCE in the OSD directly:
CENTER REAR R & L SUB OFF
Refer also to the chapter “Setting Up the Surround
Sound System” for more information.
8. DYNAMIC RANGE
The DYN. R button, which can be used only in
combination with a Dolby Digital source, incremental-
ly reduces the audio track’s dynamic range in four
steps (100%, 75%, 50% and 25%) to allow for com-
fortable listening under a variety of conditions. The
normal or default position is 100%.
To adjust the dynamic range, each consecutive
press of the
DYN. R button will reduce the value in
25% increments, as shown in the alpha-numeric dis-
play section.
NOTE:
Although we usually prefer to reproduce a source’s
full dynamic range (the difference between very loud
and very soft sounds), it may occasionally be desir-
able to reduce the dynamic range. For example,
when playing a movie late at night, loud explosions
might wake sleeping family members. Simply turning
the volume control down would probably make a
whisper in the next scene inaudible. The
DYN. R but-
ton solves this dilemma by progressively lowering the
volume of loud peaks while increasing the level of
softer sounds.
9. MODE
The MODE button scrolls through the available sur-
round sound modes. The button functions in the
same way as the
SURROUND MODE button on the
T 760 front panel (No. 11 on front panel drawing).
The selected Surround mode is permanently indi-
cated in the display area and is also shown for 3 sec-
onds in the alpha-numeric display section.
10. CD PLAYER CONTROL
(for use with NAD CD Players).
;engages Pause
9 engages Stop
NA
D
16
GB
To Next Page
Loading...
