NAMRON DIY ZigBee RGBW LED Controller
09.ZGDIYRGBW.04282
Function introduction
Important: Read All Instructions Prior to Installation
12VDC Input
Common Anode output (+)
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
Product Data
Safety & Warnings
Input Voltage
Output Type
Output Current
12/24VDC
Constant voltage72W@12V, 144W@24V
4CH, 1.5A/CH
Output Power
No.
1
Dimension (LxWxH)
84x20x14mm
CH 3 (B) output (-)
CH 2 (G) output (-)
CH 1 (R) output (-)
CH 4 (W) output (-)
• Mini size zigbee RGBW LED light device based on latest ZigBee 3.0 protocol
• Enables to control ON/OFF, light intensity and RGB color of connected RGBW LED lights
• ZigBee end device that supports Touchlink commissioning
• Supports find and bind mode to bind a ZigBee remote
• Compatible with universal ZigBee gateway products
• Waterproof grade: IP20
• W channel can be controlled through Gateway’s color temperature control interface
• W channel can be controlled separately from RGB channels through RGBW zigbee remote or touch
panel’s W button
• Supports self-forming zigbee network without coordinator
• Supports zigbee green power and can bind max. 20 zigbee green power remotes
Operation
1.Do wiring according to connection diagram correctly.
2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible
systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee
system.
3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)
4. TouchLink to a Zigbee Remote
< 10cm
Note: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.
2) TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.
3) For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink.
4) After TouchLink, the device can be controlled by the linked remotes.
V+ V+
R- R-
G- G-
W- W-
B- B-
Zigbee
Remote
Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will
fail. Please refer to the part "Factory Reset Manually".
Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as
instructed by the controller.
Step 3: Re-power on the device to set it into network pairing mode (connected light flashes twice slowly), 15
minutes timeout, repeat the operation.
Step 1: Method 1: Re-power on the device 4 times to start Touchlink commissioning immediately, 180S timeout,
repeat the operation.
Method 2: Re-power on the device, Touchlink commissioning will start after 15 if it’s not added to a
zigbee network, 165S timeout. Or start immediately if it’s already added to a network, 180S timeout. Once
timeout, repeat the operation.
minutes
Step 2: Bring the remote or touch panel within 10cm of the lighting device.
Step 3: Set the remote or touch panel into Touchlink commissioning,
please refer to corresponding remote or touch panel manual to learn how.
Step 4: Connected light will blink 5 times
and then stay solid on, then the device
will appear in your controller's menu and
can be controlled through controller or
hub interface.
Step 4: There shall be
indication on the
remote for successful
link and connected
light will flash twice.
5. Removed from a Zigbee Network through Coordinator or Hub Interface
From your ZigBee controller or hub interface, choose to delete or reset the
lighting device as instructed. The connected light blinks 3 times to indicate
successful reset.
AC Power
50/60Hz
L
N
G
V+
V-
OUTPUT
INPUT
12/24V
CV PSU
Input Voltage:DC 12-24V
Output Current:4x1.5A max.
Max Output Power:72-144W
ZigBee RGBW LED Controller
DC INPUT
Red:V+
Black:V-
LED OUTPUT
Black:LED+
Red:R-
Green:G-
Blue:B-
White:W-
Input Voltage:DC 12-24V
Output Current:4x1.5A max.
Max Output Power:72-144W
ZigBee RGBW LED Controller
DC INPUT
Red:V+
Black:V-
LED OUTPUT
Black:LED+
Red:R-
Green:G-
Blue:B-
White:W-
AC Power
50/60Hz
L
N
G
V+
V-
OUTPUT
INPUT
12/24V
CV PSU
Input Voltage:DC 12-24V
Output Current:4x1.5A max.
Max Output Power:72-144W
ZigBee RGBW LED Controller
DC INPUT
Red:V+
Black:V-
LED OUTPUT
Black:LED+
Red:R-
Green:G-
Blue:B-
White:W-
V+ V+
R- R-
G- G-
W- W-
B- B-
Note: 1) W channel can be turned on through Gateway’s color temperature control interface which will mix RGB
channels as 1 channel white and then make color tuning with the 4th channel white. Once turned on, the
brightness of white channel will be controlled together with RGB channels.
2) W channel can be controlled separately from RGB channels through RGBW zigbee remote or touch panel’s
W button, please refer to their manuals.
To Next Page
Need help?
General
