Nautilus Bowflex C7 - Routine Maintenance; Daily, Weekly, Monthly Tasks; Drive Belt Tension Check

5
MAINTENANCE
Read all maintenance instructions fully before you start any repair work. In some conditions, an assistant is required to do
the necessary tasks.
(TXLSPHQWPXVWEHUHJXODUO\H[DPLQHGIRUGDPDJHDQGUHSDLUV7KHRZQHULVUHVSRQVLEOHWRPDNHVXUHWKDW
UHJXODUPDLQWHQDQFHLVGRQH:RUQRUGDPDJHGFRPSRQHQWVPXVWEHUHSDLUHGRUUHSODFHGLPPHGLDWHO\
2QO\PDQXIDFWXUHUVXSSOLHGFRPSRQHQWVFDQEHXVHGWRPDLQWDLQDQGUHSDLUWKHHTXLSPHQW
 ,IDWDQ\WLPHWKH:DUQLQJODEHOVEHFRPHORRVHXQUHDGDEOHRUGLVORGJHGUHSODFHWKHODEHOV,ISXUFKDVHG
in US/Canada, contact Customer Service for replacement labels. If purchased outside US/Canada, contact
your local distributor for them.
'LVFRQQHFWDOOSRZHUWRWKHPDFKLQHEHIRUH\RXVHUYLFHLW
Daily: Before each use, examine the exercise machine for loose, broken, damaged, or worn parts. Do not
XVHLIIRXQGLQWKLVFRQGLWLRQ5HSDLURUUHSODFHDOOSDUWVDWWKH¿UVWVLJQRIZHDURUGDPDJH0DNH
sure adjustment knobs are tight. Tighten as necessary. Check the Pedals and tighten as necessary.
After each workout, use a damp cloth to wipe your machine and Console free of moisture.
NOTICE: If necessary, only use a mild dish soap with a soft cloth to clean the Console. Do not clean
with a petroleum based solvent, automotive cleaner, or any product that contains ammo-
nia. Do not clean the Console in direct sunlight or at high temperatures. Be sure to keep
the Console free of moisture.
Weekly: Clean the machine to remove any dust, dirt, or grime from the surfaces.
&KHFNSHGDOVDQGFUDQNDUPVDQGWLJKWHQDVQHFHVVDU\0DNHVXUHDOOEROWVDQGVFUHZVDUHWLJKW
Tighten as necessary.
Check for smooth seat operation.
1RWH Do not use petroleum based products.
Monthly
or after 20 hours:
Check the drive belt tension and adjust if necessary.
:HUHFRPPHQGWKDWWKH3HGDOVEHUHSODFHGHYHU\\HDUWRPDLQWDLQPD[LPXPXVHUVDIHW\DQGSHUIRUPDQFH
2QO\XVHUHSODFHPHQW3HGDOVDYDLODEOHIURP1DXWLOXV2WKHUEUDQGVRI3HGDOVPD\QRWEHGHVLJQHGIRU
,QGRRU&\FOLQJRUWKLVSURGXFWDQGFDQFDXVHGDQJHUWRXVHUVDQGE\VWDQGHUVDQGZLOOYRLGWKHZDUUDQW\
&KHFNLQJWKH'ULYH%HOW7HQVLRQ
To check the Drive Belt tension, the bike needs to be operated. Get the pedals rotating
DWDERXW5307KHQVXGGHQO\LQFUHDVHWKH530WR\RXUPD[LPXPDELOLW\,IWKH
pedals move normally with no slipping, the tension is correct. If the Pedals slip, the belt
needs to be adjusted.
$GMXVWLQJWKH'ULYH%HOW7HQVLRQ
1. To change the tension of the Drive Belt, loosen the Axle Nuts. Use a 19mm open
end wrench to hold the Axle Nut on one side steady, and loosen the Axle Nut on
the opposite side with a 19mm socket and wrench.
2. If the Drive Belt is too loose and slipping, use a 10mm wrench to turn each Fly-
wheel Retainer Nut a 1/4 turn to the right (clockwise).
3. Re-test the tension of the Drive Belt, and adjust if still necessary.
$GHWDLOHG³$GMXVWWKH%HOW7HQVLRQ´SURFHGXUHFDQEHIRXQGLQWKLV6HUYLFH0DQXDO
)O\ZKHHO5HWDLQHU1XWV
$[OH1XW