Need help?Do you have a question about the NETGEAR WAX630 and is the answer not in the manual?
General| 2.4 GHz | Yes |
|---|---|
| MIMO type | Multi User MIMO |
| Modulation | OFDM |
| Number of users | 200 user(s) |
| Networking standards | IEEE 802.11ax, IEEE 802.11i, IEEE 802.3af, IEEE 802.3at |
| Spread spectrum method | OFDM, OFDMA |
| Ethernet LAN data rates | 100, 1000, 2500 Mbit/s |
| Maximum data transfer rate | 6000 Mbit/s |
| Maximum data transfer rate (5 GHz) | 2400 Mbit/s |
| Maximum data transfer rate (2.4 GHz) | 1200 Mbit/s |
| Output current | 3.5 A |
| Output voltage | 12 V |
| Placement | Ceiling, Wall |
| Product color | White |
| Antenna type | Internal |
| Antenna gain level (max) | 4.3 dBi |
| Operating temperature (T-T) | 0 - 40 °C |
| Security algorithms | EAP-TLS, PEAP, SSL/TLS, TTLS, WPA, WPA2, WPA3 |
| Service Set Identifier (SSID) features | SSID broadcast, SSID broadcast on/off |
| Number of products included | 1 pc(s) |
| USB 2.0 ports quantity | 0 |
| Ethernet LAN (RJ-45) ports | 1 |
| Harmonized System (HS) code | 85176990 |
Weight and Dimensions| Depth | 268.29 mm |
|---|---|
| Width | 266.61 mm |
| Height | 55.5 mm |
| Weight | 956 g |
Outlines essential safety guidelines to prevent injury and equipment damage during use.
Guides users through the physical connection of the access point to their network via Ethernet.
Explains the methods available to connect to the access point for its first-time setup.
Details connecting the access point via the cloud portal for remote management by subscribers.
Describes connecting the access point using the mobile app for remote management by subscribers.
Guides setting up the access point via WiFi using its local browser interface.
Guides setting up the access point via a wired LAN connection using its local browser interface.
Explains how to configure the access point offline by connecting a computer directly via Ethernet.
Details how to add an access point as an extender using the Insight Cloud Portal.
Details adding an access point as an extender using the Insight mobile app.
Guides creating new WiFi networks (SSIDs) with various security options like WPA2/WPA3.
Details changing the security protocols (WPA2, WPA3) and encryption methods for WiFi networks.
Guides setting up a basic portal where users click through a splash page for access.
Details configuring the access point to use a captive portal hosted by an external vendor.
Explains the process of registering the access point to enable Facebook Wi-Fi functionality.
Guides setting up a captive portal that uses a Facebook business page for user check-ins.
Details setting up MAC ACLs to allow or deny access to WiFi networks based on device MAC addresses.
Covers disabling DHCP and manually assigning a static IP address to the access point.
Guides configuring VLAN IDs for untagged and management traffic to segment the network.
Allows switching between NETGEAR Insight remote management and local browser UI management.
Guides changing the administrator password for accessing the local browser UI.
Details checking for, downloading, and updating the access point's firmware to the latest version.
Describes how to reset the access point to its original factory default configuration.
Allows configuring the access point's network addressing mode as either NAT or Bridge.
Guides selecting a pre-configured MAC Access Control List (ACL) to apply to a specific WiFi network (SSID).
Allows setting upload and download bandwidth limits for devices connected to a WiFi network.
Provides step-by-step instructions for configuring a WiFi bridge connection between two access points using WDS.
Guides performing a ping test to verify network connectivity and troubleshoot communication issues.
Details capturing WiFi and Ethernet packets for network analysis, debugging, and troubleshooting.
Offers general advice and common checks for resolving WiFi connectivity issues with client devices.
Provides guidance on interpreting LED status indicators for diagnosing access point operational issues.
Offers troubleshooting steps for when extender and root access points fail to establish a mesh connection.
Provides steps to diagnose and resolve issues preventing WiFi client devices from connecting.
Guides troubleshooting login issues when accessing the access point via a wired LAN connection.
Details troubleshooting steps for login blockage due to multiple incorrect password attempts.
To Next Page
