Need help?Do you have a question about the Nexo RS15 and is the answer not in the manual?
General| Weight | 32 kg (70.5 lbs) |
|---|---|
| Crossover Frequencies | 80Hz - 120Hz |
| Enclosure | Bass-reflex |
| Connectors | 2 x NL4 |
| Power Handling | 800 Watts nominal |
| Sensitivity | 101 dB SPL nominal |
| Enclosure Type | Bass-reflex |
| Components | 1 x 15" (38cm) long excursion 4Ω driver. |
| Usable Range @-6dB | 30Hz - 130Hz |
Explains the advantages and technical principles of RAY SUB technology for low frequency control.
Details permissible noise level exposures according to OSHA and recommends hearing protection.
Emphasizes understanding rigging and stacking safety rules before system deployment.
Warns about earthing requirements for NEXO apparatus and mains cord connection.
Explains how to configure RS15 cabinets as 'Left' or 'Right' using skids for optimized flexibility.
Provides instructions for mounting optional accessories like handles and flying plates.
Details the procedure for mounting RS15 wheels on the back panel of the cabinet.
Describes how to use the RS15 dolly for transporting up to 3 RS15 cabinets and a bumper.
Explains configuring connector plates and wiring for Omni and Directional modes.
Provides recommendations on multi-conductor cables and calculations for maximum cable length.
Lists recommended amplifier power ratings for Omni and Directional modes with RS15.
Explains amplifier current capacity, gain settings, and practical considerations for alignment.
Describes the rear panel connectors of NXAMP4x1 and NXAMP4x4, including analog and digital I/O.
Provides recommended configurations for RS15 with NXAMP in Omni and Directional modes.
Details optimized parameters for GEO S12 TDController used with RS15 in omni mode.
Lists available setups combining RS15 with NEXO speakers in NX242/NXAMP.
Illustrates the connection diagram for RS15 with GEOS12 TDController in Mono Omni Mode.
Shows the connection diagram for RS15 with NX242-ES4 TD Controller in Stereo Omni Mode.
Presents the connection diagram for RS15 with NX242-ES4 TD Controller in Stereo Directional Mode.
Illustrates the connection diagram for RS15 with NXAMP in Stereo Omni Mode.
Shows the connection diagram for RS15 with NXAMP in Stereo Directional Mode.
Outlines critical safety precautions for flying RS15 systems, including inspections and personnel requirements.
Addresses safety concerns related to unstable ground-stacked PA systems and proper stacking procedures.
Provides contact information for training agencies related to loudspeaker flying systems.
Details procedures for flying RS15 arrays, including hoist rating and connecting the first unit.
Explains how to adjust the bumper rigging point to achieve perfect horizontality for flown arrays.
Details flying the second RS15 and repeating steps for subsequent cabinets.
Provides guidance on regular testing, maintenance, and cleaning of the RS15 flying system components.
Discusses common challenges in low frequency coverage, such as wavelength control and room modes.
Explains the advantages of gradient subwoofers, including front-to-rear attenuation and reduced sensitivity to room modes.
Covers monophonic and stereo subwoofer array design principles and considerations.
Details the implementation of omnidirectional mode for single RS15 and RS15 arrays.
Explains directional mode and RS15s pair configurations: alternate, back to back, face to face.
Explains steered array techniques and delay value implementation for coverage control.
Shows coverage control over distance with a steering delay sequence for a 15° tilt down.
Defines the acoustic reference points for RS15 in Omni and Directional modes for system alignment.
Describes aligning RS15s with main systems using distance and phase measurements.
Lists essential tools and equipment required for system installation, including software and measurement devices.
Details configuration checks for NX Digital TDcontrollers, including output assignment and parameters.
Checks amplifier configuration, connections, and ensures proper speaker connectivity.
Guides final checks before sound check, including CD track playback for system verification.
Details product features, system specifications, operation, and shipping information.
Provides dimensions and diagrams for frequency response and impedance of the RS15 subwoofer.
Presents polar plots showing coverage patterns for RS15 in Omni and Directional modes.
Details specifications and dimensions for various RS15 accessories like bumpers, plates, wheels, and dollies.
Lists detailed specifications for the GEO S12 Analogue TDController.
Shows front and rear panel views of the GEO S12 Analogue TDController.
Details specifications for the NX242 Digital TDController with NX-Tension Card.
Presents front and rear panel views of the NX242 Digital TDController.
Lists specifications for NXAMP4x1 and NXAMP4x4 Powered Digital TDControllers.
Details user controls for NXAMP, including system selection and setup.
Shows front and rear panel views of the NXAMP4x1 and NXAMP4x4.
Lists main modules and control electronics for the RS15 system.
Provides a list of available parts and accessories for the RS15 system.
Provides contact information and website for Nexo S.A.
To Next Page
