Nextron MASTERTRACE - Setpoint Values Menu: Single-Phase Modules

5.10
MASTER TRACE Chapter 5 Operation
SETPOINTS:
OPERATING VALUES
[MESSAGEô ]
SELECT HT:1-1?
NONAME &
[MESSAGEô ]
HEATER ENABLED?
yes
?
[MESSAGEô ]
HEATER SETPOINT:
5°C
?
[MESSAGEô ]
LOW TEMPERATURE
ALARM: 2°C
?
[MESSAGEô ]
HIGH TEMPERATURE
ALARM: off
?
[MESSAGEô ]
LOW CURRENT
ALARM: off
?
[MESSAGEô ]
HIGH CURRENT
ALARM: off
?
[MESSAGEô ]
HIGH CURRENT
TRIP: off
?
[MESSAGEô ]
POWER LIMIT
CURRENT: off
?
[MESSAGEô ]
GROUND FAULT
ALARM: 20mA
?
[MESSAGEô ]
GROUND FAULT
TRIP: 30mA
?
[MESSAGEô ]
HEATER VOLTAGE:
120V
?
[MESSAGEô ]
LOW VOLTAGE:
ALARM: off
?
[MESSAGEô ]
go to 3
[SETPOINT]
ò
1
[SETPOINT]
ò
SETPOINTS:
HEATER SETUP
[MESSAGEô ]
SELECT HT: 1-1?
NONAME &
[MESSAGEô ]
HTR 1-1 NAME:
NONAME
?
[MESSAGEô ]
MASTER OVERRIDE:
off
?
[MESSAGEô ]
PROPORTIONAL
CONTROL: off
?
[MESSAGEô ]
DEADBAND
2 C°
?
[MESSAGEô ]
IF RTD FAILS
HEATER GOES: off
?
[MESSAGEô ]
COPY TO OTHER
HEATERS: no
?
[MESSAGEô ]
go to 4
[SETPOINT]
3 4
ò
DISPLAY MODE:
normal user
?
[MESSAGEô ]
DEFAULT DISPLAY:
system status
?
[MESSAGEô ]
DISPLAY TIMEOUT:
60 seconds
?
[MESSAGEô ]
SCAN TIME:
3 seconds
?
[MESSAGEô ]
TEMPERATURE
UNITS: celcius
?
[MESSAGEô ]
COST PER kWh:
$0.05
?
[MESSAGEô ]
STAGGER START:
off
?
[MESSAGEô ]
NUM OF AMB SENSE
HTRS: 0
?
[MESSAGEô ]
SETPOINTS:
SYSTEM SETUP
[MESSAGEô ]
MODULE RANGE:
1-30
?
[MESSAGEô ]
MODULE LIST:
MOD: 1? SEL:yes?
[MESSAGEô ]
[SETPOINT]
ò
6
MANUAL SYSTEM:
ALARM: disabled
?
[MESSAGEô ]
GF TEST:
test now
?
[MESSAGEô ]
go to 1
SETPOINTS:
SETPOINTS TEST
[MESSAGEô ]
MANUAL ALARM:
disabled
?
[MESSAGEô ]
MANUAL HEATER:
disabled ?
[MESSAGEô ]
BAUD RATE MR100:
1200
?
[MESSAGEô ]
BAUD RATE 1:
1200
?
[MESSAGEô ]
go to 5
RESET CONTROL
MODULE? no
?
[MESSAGEô ]
SET MODULE
NUMBER: no
?
[MESSAGEô ]
RESET MR100:
no
?
[MESSAGEô ]
FIRMWARE VERSION:
D1-02-01
[MESSAGEô ]
MANUAL VERSION:
1501-0006_1
[MESSAGEô ]
FOR ASSISTANCE:
(403) 735-9555
[MESSAGEô ]
go to 6
5
ò
Restrictions
1 1- & 2-point Modules
2 5- & 10-point Modules
3 Dual RTD Modules
4 Solid-State Switch Modules
5 MR100 Interface Module
Advanced User Mode
4
1
3
4
5
5
5
5
READ MODULE
NUMBER: 1
?
[MESSAGEô ]
ALARM CONTACTS:
MECH: NC
?
SS: NC
?
[MESSAGEô ]
5
5
ðð
ð
2
5.4 Setpoint Values Menu: Single-Phase Modules
RTD BOARD:
On Board
?
[MESSAGEô ]
AMBIENT SENSING
HEATER: None
?
[MESSAGEô ]
5
TRACECHECK CYCLE
TIME: off
?
[MESSAGEô ]
go to 2
2
TRACECHECK HTR ON
TIME: 0.5 MIN ?
[MESSAGEô ]
2
RTD MODE
2 RTDs, lowest
[MESSAGEô ]
2
BAUD RATE 2:
1200
?
[MESSAGEô ]
ALARM LIGHT MODE:
alarm off
?
[MESSAGEô ]
5
2
AMBIENT RTD
TEMP: 5°C
&
[MESSAGEô ]
5