What to do if my Nilfisk-Advance BR 752 doesn't move and shows an error code?
If your Nilfisk-Advance Scrubber does not move and the display shows an error code, it might be because the machine was turned on while keeping the drive pedal pressed. Release the drive pedal. If the problem continues, contact an authorised Service Center.
What does it mean if my Nilfisk-Advance BR 752 Scrubber displays an error code different from 't4'?
If the display of your Nilfisk-Advance Scrubber shows an error code, and the code is different from “t4”, it indicates that the machine's electronic control system is in an alarm condition. Turn off the machine and then turn it on again. If the problem persists, contact an authorised Service Center.
Why is the dirty water vacuuming insufficient on my Nilfisk-Advance BR 752?
If the dirty water vacuuming of your Nilfisk-Advance Scrubber is insufficient, several factors could be at play. The recovery tank might be full, so try emptying it. The vacuum grid could be clogged, or the float might be closing, in which case you should clean the vacuum grid. Check if the container with the debris collection grid is clogged and clean it if necessary. Also, ensure the hose is properly connected to the squeegee. The squeegee itself might be dirty, or the blades could be worn or damaged, requiring cleaning or replacement. Finally, verify that the tank cover is correctly closed and the gasket is in good condition; if not, close it properly or clean/replace the gasket.
What to do if the 3 warning lights flash simultaneously on my Nilfisk-Advance BR 752 Scrubber?
If the 3 warning lights on your Nilfisk-Advance Scrubber flash simultaneously, it indicates that the brush motors are overloaded. To resolve this, try using less aggressive brushes and avoid working with extra pressure turned on. Another possible cause is foreign materials, such as tangled threads, preventing the brushes from rotating. In this case, you should clean the brush hubs.
Why does the squeegee leave marks on the floor when using my Nilfisk-Advance BR 752 Scrubber?
If the squeegee on your Nilfisk-Advance Scrubber leaves marks on the floor, it could be due to several reasons. Check for any debris under the squeegee blades and remove it. If the squeegee blades are worn, chipped, or torn, overturn or replace them. Also, ensure that the squeegee is properly balanced with the handwheel and adjust if necessary.
What to do if the brushes don't work and the red warning light flashes on my Nilfisk-Advance Scrubber?
If the brushes on your Nilfisk-Advance Scrubber do not work and the red warning light flashes, it's likely that the batteries are discharged. To fix this, charge the batteries.
Why don't the motors work and no warning light turns on in my Nilfisk-Advance Scrubber?
If the motors of your Nilfisk-Advance Scrubber do not work and no warning light turns on, it could be due to a disconnected battery connector. Try connecting it. Alternatively, the batteries might be discharged, so you should charge them.
Why is the solution flow insufficient in my Nilfisk-Advance BR 752 Scrubber?
If the solution flow is insufficient in your Nilfisk-Advance Scrubber, it could be due to several reasons. The solution tank might be empty, so try filling it. Alternatively, the solution filter could be dirty, requiring you to clean it. If your machine has the optional EcoFlex™ system, the tank might be dirty or encrusted, in which case you should drain it.
Why does the LED flash and the brushes not work at start-up of my Nilfisk-Advance BR 752?
If, at the start-up of your Nilfisk-Advance Scrubber, the LED of the switch flashes and the brushes do not work, it's possible that the machine was turned off without lifting the brush deck. Wait for the deck to lift before turning on the brushes again by pressing the switch.
General| Model | BR 752 |
|---|---|
| Solution Tank Capacity | 114 L (30 gal) |
| Recovery Tank Capacity | 114 L (30 gal) |
| Brush Speed | 250 rpm |
| Power Source | Battery |
| Cleaning Width | 750 mm |
| Working width | 750 mm |
To Next Page
