Notifier FMM-1 FlashScan

DN-6720 • 08/23/04 — Page 1 of 6
GENERAL
Four different monitor modules are available for NOTIFIER in-
telligent controls to suit a variety of applications. Monitor mod-
ules are used to supervise a circuit of dry-contact input de-
vices, such as conventional heat detectors and pull stations,
or monitor and power a circuit of two-wire smoke detectors
(FZM-1).
FMM-1 — is a standard-sized module (typically mounts to
a 4" [10.16 cm] square box) that supervises either a Class A
(Style D) or Class B (Style B) circuit of dry-contact input de-
vices.
FMM-101 — is a miniature monitor module (a mere 1.3"
(3.302 cm) H x 2.75" (6.985 cm) W x 0.5" (1.270 cm) D) used
to supervise a Class B (Style B) circuit. Its compact design
allows the FMM-101 to often be mounted in a single-gang
box behind the device it’s monitoring.
FZM-1 — is a standard-sized module used to monitor and
supervise compatible two-wire, 24 volt, smoke detectors on
a Class A (Style D) or Class B (Style B) circuit.
FDM-1 — is a standard-sized dual monitor module used to
monitor and supervise two independent two-wire initiating
device circuits (IDCs) at two separate, consecutive addresses
in intelligent, two-wire systems.
FlashScan® (U.S. Patent 5,539,389) is a new communi-
cation protocol developed by NOTIFIER Engineering that
greatly enhances the speed of communication between ana-
log intelligent devices. Intelligent devices communicate in a
grouped fashion. If one of the devices within the group has
new information, the panel CPU stops the group poll and
concentrates on single points. The net effect is response
speed greater than five times that of other designs.
FlashScan® is a registered trademark of NOTIFIER.
FMM-1 MONITOR MODULE
• Built-in type identification automatically identifies this de-
vice as a monitor module to the control panel.
• Powered directly by two-wire SLC loop. No additional power
required.
• High noise (EMF/RFI) immunity.
• SEMS screws with clamping plates for ease of wiring.
• Direct-dial entry of address: 01 – 159 on FlashScan® sys-
tems, 01 – 99 on CLIP systems.
• LED flashes green during normal operation (this is a pro-
grammable option) and latches on steady red to indicate
alarm.
The FMM-1 Monitor Module is intended for use in intelli-
gent, two-wire systems, where the individual address of each
module is selected using the built-in rotary switches. It pro-
vides either a two-wire or four-wire fault-tolerant Initiating
Device Circuit (IDC) for normally-open-contact fire alarm and
supervisory devices. The module has a panel-controlled LED
indicator. The FMM-1 can be used to replace MMX-1 mod-
ules in existing systems.
FMM-1, FMM-101, FZM-1, FDM-1
Monitor ModulesMonitor Modules
Monitor ModulesMonitor Modules
Monitor Modules
with FlashScan®with FlashScan®
with FlashScan®with FlashScan®
with FlashScan®
August 23, 2004
DN-6720 • H-220
Section: Intelligent/Addressable Devices
FMM-1
and
FZM-1
6724mod2.tif
FMM-1 Applications — Use to monitor a zone of four-
wire smoke detectors, manual fire alarm pull stations,
waterflow devices, or other normally-open dry-contact alarm
activation devices. May also be used to monitor normally-
open supervisory devices with special supervisory indica-
tion at the control panel. Monitored circuit may be wired as
an NFPA Style B (Class B) or Style D (Class A) Initiating
Device Circuit. A 47K ohm End-of-Line Resistor (provided)
terminates the Style B circuit. No resistor is required for su-
pervision of the Style D circuit. Maximum IDC loop length is
2,500 ft./762 m (20 ohms maximum).
S635
CS669
MEA
143-01-E (FDM-1)
317-01-E
(FMM-1/-101)
345-02-E
(FMM-1/-101)
457-99-E (FZM-1,
FMM-1/-101)
447-99-E
detail of FDM-1
— note “ones”
addresses are
0, 2, 4, 6, 8 only
6720fdm1.tif
This document is not intended to be used for installation purposes. We try to keep our
product information up-to-date and accurate. We cannot cover all specific applications
or anticipate all requirements. All specifications are subject to change without notice.
For more information, contact NOTIFIER. Phone: (203) 484-7161 FAX: (203) 484-7118
12 Clintonville Road, Northford, Connecticut 06472
NOTIFIER® is a Honeywell company.
U.S. Coast Guard
161.002/23/3 (AFP-200:
FMM-1/-101, FZM-1)
161.002/42/1
(NFS-640: FMM-1/-101)
93/60141 (E3)
(FMM-1/-101, FZM-1)
94/60004/E2
(AFP200:
except FDM-1)
02/60007
(NFS-640: FDM-1)
7300-0028:202
California
State Fire
Marshal

Notifier FMM-1 FlashScan Specifications

General

Model	FMM-1
Type	FlashScan Monitor Module
Operating Voltage	15 to 32 VDC
Operating Temperature	32°F to 120°F (0°C to 49°C)
Humidity	10% to 93% non-condensing
Compatibility	Notifier Fire Alarm Control Panels
Max. SLC Standby Current	375 μA
Max. SLC Alarm Current	375 μA
Standby Current	1.5 mA
Alarm Current	5.0 mA

Summary

General Overview of NOTIFIER Monitor Modules

FMM-1 Monitor Module Description

Details the standard-sized monitor module used to supervise dry-contact input devices.

FMM-101 Miniature Monitor Module Description

Covers the miniature monitor module for supervising a Class B circuit of dry-contact input devices.

FZM-1 Interface Module Description

Explains the module used to monitor compatible two-wire, 24 volt, smoke detectors.

FDM-1 Dual Monitor Module Description

Describes the dual monitor module for supervising two independent two-wire circuits.

FlashScan Communication Protocol

Introduces the protocol that enhances response speed of analog intelligent devices.

FMM-1 Monitor Module Details

FMM-1 Operation and Features

Explains module operation, LED indication, and features like type identification and SEMS screws.

FMM-1 Applications

Details the use of the FMM-1 to monitor normally-open-contact fire alarm and supervisory devices.

FMM-1 Specifications

Lists the nominal voltage, current draw, EOL resistance, and dimensions for the FMM-1.

FMM-101 Miniature Monitor Module Details

FMM-101 Operation and Features

Covers operation, LED status, and features like miniature size and direct-dial addressing.

FMM-101 Applications

Describes monitoring single devices or zones of four-wire smoke detectors with the FMM-101.

FMM-101 Specifications

Provides operating voltage, current, EOL resistance, and dimensions for the FMM-101.

FZM-1 Interface Module Details

FZM-1 Operation and Features

Explains operation, LED indicators, and features like supervision of IDC wiring and external power.

FZM-1 Applications

Details using FZM-1 to monitor two-wire conventional smoke detectors on Style B or D circuits.

FZM-1 Specifications

Lists voltage, current, EOL resistance, external supply voltage, and dimensions for FZM-1.

FDM-1 Dual Monitor Module Details

FDM-1 Overview and Features

Describes the dual monitor module for two independent Class B initiating device circuits.

FDM-1 Automatic Addressing

Explains how the FDM-1 automatically assigns itself to two addressable points.

FDM-1 Applications

Details the FDM-1's use for monitoring normally open contact fire alarm, supervisory, or security devices.

FDM-1 Specifications

Lists operating voltage, current draw, EOL resistance, and dimensions for the FDM-1.

Module Installation Guidelines

Standard Module Mounting

Instructions for mounting FMM-1, FDM-1, and FZM-1 modules to electrical boxes or backboxes.

FMM-101 Module Mounting

Guidance for wiring and mounting the FMM-101 without rigid connections in electrical boxes.

Wiring Diagrams

FDM-1 Wiring Diagram

Illustrates the typical dual two-wire Style B initiating device circuit configuration for FDM-1.

FMM-101 Wiring Diagram

Shows the typical two-wire Style B initiating device circuit configuration for FMM-101.

FMM-1 Wiring Diagrams

Provides diagrams for FMM-1 in Style B, Style D, and security system configurations.

FZM-1 Wiring Diagrams

Illustrates FZM-1 interface wiring for two-wire conventional detectors in Style B and Style D.

FRM-1 Relay Control Module Wiring

Shows wiring for the FRM-1 relay control module used to disconnect a power supply.