This document is a user guide for the Oasis Aqua Pointe Modular Series Electronic Bottle Fillers, including models MWEBF, MW8EBF, MW12EBF, MWSMEBF, MWSM8EBF, MWSM12EBF, MEBF, M8EBF, M12EBF, MEBFEE, M8EBFEE, and M12EBFEE. It provides instructions for installation, operation, and maintenance of these units.
Function Description:
The Oasis Aqua Pointe Modular Series Electronic Bottle Fillers are designed to provide convenient and efficient water dispensing for refilling bottles. These units can be installed as wall-mounted or surface-mounted systems and are available with or without an integrated chiller. The electronic controls allow for hands-free operation and include features such as bottle count tracking and filter life monitoring.
Important Technical Specifications:
- Water Supply Pressure: Designed to operate at a water supply line pressure of up to 100 psi (690 kPa). A pressure regulator is required if pressure exceeds this limit.
- Electrical Connection: 115V grounded North American duplex receptacle. Intended to be connected to a 20A minimum Ground Fault Circuit Interrupting (GFCI) device to meet UL requirements. Flexible conduit is recommended for power supply to the junction box and chiller (if used).
- Filter Capacity (VersaFilter III): Default capacity is 4750 gallons (18000 liters). Other filter capacities (1250 GAL/5000 LTR for VersaFilter I, 3000 GAL/11000 LTR for VersaFilter II) are configurable.
- Bottle Count: Default bottle count is 0.5L (1 Bottle).
- Flow Rate: Default flow rate is 1.0 GPM (3.8 LPM).
- Maximum Dispense Time: Default maximum dispense time is 20 seconds, configurable to 10 or 30 seconds.
- Compressor (systems with chiller): Equipped with an automatic reset protector for overload protection.
- Dimensions: Detailed rough-in drawings are provided for various models, showing wall opening dimensions, mounting hole locations, and plumbing connections in inches and millimeters.
- MWEBF, MW8EBF, MW12EBF (Wall-mounted): Wall opening approximately 19-7/8" (505mm) wide by 40" (1016mm) high. Overall height from floor line to top of unit is approximately 40-3/4" (1035mm).
- MEBF, M8EBF, M12EBF, MEBFEE, M8EBFEE, M12EBFEE (Wall-mounted with fountain): Wall opening approximately 19-7/8" (251mm) wide by 40" (1016mm) high. Overall height from floor line to top of unit is approximately 44-11/16" (1135mm).
- MWSMEBF, MWSM8EBF, MWSM12EBF (Surface-mounted): Overall width approximately 20-5/16" (516mm). Overall height from floor line to top of unit is approximately 41-5/16" (1049mm).
Usage Features:
- Hands-Free Operation: The units are designed for hands-free use, with a remote push button for accessing menu settings.
- LED Indicator Key:
- GREEN: "BOTTLES SAVED" - Standby mode, filter life <80% used. No action needed.
- YELLOW: "BOTTLES SAVED" - Standby mode, filter life >80% but <100% used. Order new filter.
- RED: "BOTTLES SAVED" - Standby mode, filter life =100% used. Replace the filter.
- Configurable Settings: Users can access a menu via a pushbutton to adjust various settings:
- Units: Switch between Gallons and Liters.
- Filter Status: Toggle between Unfiltered and Filtered unit.
- Flow Rate: Adjust the flow rate by changing whole gallon/liter digits and tenths digits.
- Reset Counts: Reset Gallon/Liter count or Bottle count.
- Filter Capacity: Change filter capacity settings for different VersaFilter models.
- 3 Sec Rule/Bottle Size: Switch between a "3 sec rule" (increases bottle count based on a 3-second dispense) and a 0.5L bottle setting.
- Maximum Dispense Time: Adjust the maximum dispense time to 10, 20, or 30 seconds.
- Calibration: Option to run calibration again.
- Automatic Menu Exit: The menu will exit and save settings if idle for 10 seconds (no button press), reverting to the Home Screen.
Maintenance Features:
- Condenser Cleaning (systems with chiller): The condenser should be inspected at 3-month intervals and cleaned with a vacuum attachment to remove dirt and lint.
- Lubrication (systems with chiller): The hermetically sealed compressor requires no additional lubrication. The fan motor seldom needs oiling, but if required, a few drops of SAE 10 oil should be used.
- Draining (systems with chiller): When removing the cooler from service, the unit should be drained by removing the grille, closing the supply valve, and removing the drain plug.
- Filter Replacement: The LED indicator provides visual cues for when a filter needs to be ordered (YELLOW) or replaced (RED).
- Grounding: Proper grounding is a critical requirement. The long green ground wire must be attached to the frame assembly junction box ground for proper unit function.
- Warranty: The warranty is voided if the machine is altered, modified, or combined with any other machine or device, as this may lead to flooding, electrical shock, or fire.
Need help?
General
To Next Page