To Next Page
M
Melissa HoodSep 9, 2025
Why is the printing flaking off my Oki Printer?
- AAllison HughesSep 10, 2025
Printing may flake off if the wrong media type was selected in the printer driver. Ensure you set the correct media type in the printer driver.
Why is the printing flaking off my Oki Printer?
Printing may flake off if the wrong media type was selected in the printer driver. Ensure you set the correct media type in the printer driver.
What causes repeated fine streaks on prints from my Oki C9000 Printer?
Repeated fine streaks may appear if the wrong media type was selected in the printer driver. Ensure you set the correct media type in the printer driver.
What to do if I have connection problems for wireless devices with my Oki All in One Printer?
If you're experiencing connection issues between your Oki All in One Printer and wireless devices, there are several things to check. The issue might stem from the access point devices or the wireless computers themselves. Ensure you have the latest firmware for your access point devices and the latest drivers for your wireless computer. Also, the access point device may be set to “High-Speed Mode;” try disabling this setting. If MAC Address Filtering is enabled on your access point, register the wireless card’s MAC address in the MAC Address Filtering list. Finally, multiple access points might have the same SSID. Check the SSID of access point devices in the surrounding area, including floors above and below, and check for any unauthorized access points.
How to fix Oki C9000 cannot find the network interface card?
To resolve the issue of your Oki Printer not being able to find the network interface card, try the following: * Turn the printer off and on again. * Confirm that the network interface is enabled on the printer. * Ensure there is a response to the interface card command. * Make sure the network cable is correctly connected; change the cable and try again if needed. * Run the Self-diagnostic test (with the printer on, press and hold the Test button on the print server for 3 seconds, then release it). * Verify that the IP Address, Subnet Mask, and Gateway are correct. * Ensure that the TCP/IP protocol is set to Enable. * Reset the network interface card to the factory default settings. * If DHCP, BOOTP, and RARP are not used, ensure they have been set to Disable.
What to do if Oki C9000 is not identified by the Chooser and the Setup Utility?
If your Oki Printer is not identified by the Chooser and the Setup Utility, here are a few steps you can take: * Turn the printer off and on again. * Make sure the network cable is correctly connected, and try changing the cable. * If the network resides in a Zone, ensure the correct Zone name is selected in the Chooser. * Verify that the Zone name in the utility related to the NIC is the same as the Zone name set in the NIC. * Ensure AppleTalk (or Network in some OS versions) is set to Enable at the bottom right of the Chooser. * Make sure Ethernet is selected in AppleTalk (or Network). * Confirm the print driver is selected in the Chooser. * Ensure the EtherTalk protocol is set to Enable. * Print the NIC settings and confirm that the EtherTalk Port name is not blank.
What to do if an intermediate certificate has been installed on the print server of Oki C9000?
The print server supports only one certificate. If your CA service requires both an intermediate and an SSL server certificate for your Oki Printer, install the intermediate certificate on a client PC. Then delete the intermediate certificate from the printer using the web browser or the AdminManager utility, and install the SSL server certificate on the print server.
What to do if the print server was initialized after the CSR (Certificate Signing Request) was sent to the CA service on Oki C9000 Printer?
If the print server was initialized after the CSR (Certificate Signing Request) was sent to the CA service for your Oki Printer, you must start the CSR process all over again, recreating and re-sending the CSR to the CA service.
What to do if the CSR has been deleted from the print server while application for a CA certificate is pending?
If the CSR has been deleted from the print server while application for a CA certificate is pending on your Oki Printer, you must start the CSR process all over again, recreating and re-sending the CSR to the CA service.
How to fix Error writing to Prn1 on Oki C9000?
If you receive an 'Error writing to Prn1' message on your Oki Printer, here are a few things to check: * Make sure the printer is online. * If the error indicates a paper shortage, add more paper and cancel the error. * Check if another user is currently printing; if so, wait until they are finished before printing.
How to fix EEPROM Check registers NG on Oki Printer?
If you encounter an 'EEPROM Check registers NG' error on your Oki Printer, try the following: * Confirm that the NIC is installed correctly, and then turn the printer off and on again. * Initialize the NIC.
General
