What to do if Oki All in One Printer display panel doesn't work?
If the printer display panel of your Oki All in One Printer does not display anything or remains in standby mode 10 minutes after being switched on, follow the printer shutdown sequence to switch it off. Check all cable connections before restarting the printer. If the problem persists, contact your dealer.
How to fix PostScript error occurs if a banner page is printed on Oki Printer?
If a PostScript error occurs when printing a banner page on your Oki Printer, turn the banner output Off in the client’s printer settings.
What causes repeated fine streaks on prints from my Oki C9600n Printer?
Repeated fine streaks may appear if the wrong media type was selected in the printer driver. Ensure you set the correct media type in the printer driver.
What to do if I have connection problems for wireless devices with my Oki All in One Printer?
If you're experiencing connection issues between your Oki All in One Printer and wireless devices, there are several things to check. The issue might stem from the access point devices or the wireless computers themselves. Ensure you have the latest firmware for your access point devices and the latest drivers for your wireless computer. Also, the access point device may be set to “High-Speed Mode;” try disabling this setting. If MAC Address Filtering is enabled on your access point, register the wireless card’s MAC address in the MAC Address Filtering list. Finally, multiple access points might have the same SSID. Check the SSID of access point devices in the surrounding area, including floors above and below, and check for any unauthorized access points.
How to fix Oki Printer cannot find the network interface card?
To resolve the issue of your Oki Printer not being able to find the network interface card, try the following: * Turn the printer off and on again. * Confirm that the network interface is enabled on the printer. * Ensure there is a response to the interface card command. * Make sure the network cable is correctly connected; change the cable and try again if needed. * Run the Self-diagnostic test (with the printer on, press and hold the Test button on the print server for 3 seconds, then release it). * Verify that the IP Address, Subnet Mask, and Gateway are correct. * Ensure that the TCP/IP protocol is set to Enable. * Reset the network interface card to the factory default settings. * If DHCP, BOOTP, and RARP are not used, ensure they have been set to Disable.
What to do if Oki C9600n is not identified by the Chooser and the Setup Utility?
If your Oki Printer is not identified by the Chooser and the Setup Utility, here are a few steps you can take: * Turn the printer off and on again. * Make sure the network cable is correctly connected, and try changing the cable. * If the network resides in a Zone, ensure the correct Zone name is selected in the Chooser. * Verify that the Zone name in the utility related to the NIC is the same as the Zone name set in the NIC. * Ensure AppleTalk (or Network in some OS versions) is set to Enable at the bottom right of the Chooser. * Make sure Ethernet is selected in AppleTalk (or Network). * Confirm the print driver is selected in the Chooser. * Ensure the EtherTalk protocol is set to Enable. * Print the NIC settings and confirm that the EtherTalk Port name is not blank.
How to fix Oki C9600n Printer cannot find the network print server?
If your Oki Printer cannot find the network print server, try the following: * Turn the printer off and on again. * Confirm that the network interface is enabled on the printer. * Make sure the network cable is correctly connected. If it is, try changing the cable. * If the NetWare protocol is disabled, set it to Enable. * Reset the network interface card to factory default settings.
What to do if Oki C9600n network interface card is not identified?
To resolve the issue of your Oki Printer's network interface card not being identified, consider the following steps: * Turn the printer off and on again. * Ensure the network cable is correctly connected. Try changing the cable to rule out a cable issue. * Confirm that [Microsoft network client] and [NetBEUI] have been added to the network section of the control panel. * Verify that the NetBEUI protocol is set to Enable. * Make sure the factory setting of the workgroup name is PrintServer and the computer name is ML+ the last six digits of the MAC address. * Ensure the computer name of the NIC is different from the computer name on the network.
How to fix cannot print with lpr and ftp on Oki C9600n Printer?
To fix printing issues with lpr and ftp on your Oki Printer, follow these steps: * Turn the printer off and on again. * Make sure there is a response to the ping command. * Ensure the network cable is correctly connected, and try changing it if necessary. * Make sure the host name and IP address are configured in the workstation. * Ensure the printer port name is configured in the workstation. * Use 'lp' as the default port name, as 'euc' and 'sjis' are specific to printers with PostScript available.
What to do if NG is printed in the Self-diagnostic test of Oki Printer?
If 'NG' is printed during the Self-diagnostic test on your Oki Printer, take these steps: * Confirm that the NIC is installed correctly, and then turn the printer off and on again. * Ensure the network cable is correctly connected. * Connect to a different network segment and rerun the test to see if this resolves the problem.
Explains the meaning of NOTE, CAUTION, and WARNING messages in the manual.
Provides critical safety precautions for operating the printer to avoid injury or damage.
Guides on cleaning LED heads and paper feed rollers for optimal performance.
Procedures for clearing paper jams occurring within the main printer unit.
Technical details of the printer including dimensions, speeds, memory, and power.
To Next Page
General
