EasyManua.ls Logo

Oleo-Mac GSH 400 - User Manual

Oleo-Mac GSH 400
216 pages
Go to English
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
I MANUALE DI USO E MANUTENZIONE
GB OPERATOR’S INSTRUCTION BOOK
F MANUEL D’UTILISATION ET D’ENTRETIEN
D BEDIENUNGSANLEITUNG
E MANUAL DE INSTRUCCIONES
NL GEBRUIKSAANWIJZING
GSH 400 - MTH 4000 (38.9 cm
3
)
P MANUAL DE INSTRUÇÕES
GR ΕΓΧΕΙΡΙ∆ΙΟ ΧΡΗΣΗΣ ΚΑΙ ΣΥΝΤΗΡΗΣΗΣ
CZ NÁVOD K POUŽITÍ A ÚDRŽBĚ
SK NÁVOD NA POUŽITIE A ÚDRŽBU
RUS PУKOBOДCTBO ПO ЭКCПЛУAТAЦИИ
PL INSTRUKCJA OBSŁUGI I KONSERWACJI

Table of Contents

Questions and Answers

  • M
    Marcus RodriguezJul 29, 2025
    What to do if my Oleo-Mac GSH 400 engine starts and runs, but the chain is not rotating?
    • C
      Carrie ChambersJul 29, 2025
      If your Oleo-Mac Chainsaw engine starts and runs, but the chain isn't rotating, here's what you can check: 1. Ensure the chain brake is released. 2. Verify the chain tension isn't too tight. 3. Inspect the guide bar and chain assembly. 4. Check for damage to the chain and/or guide bar. 5. Inspect the clutch drum and/or rim sprocket for damage. If necessary, contact a Servicing Dealer to replace them.
  • K
    Kelly TaylorAug 5, 2025
    Why is my Oleo-Mac GSH 400 Chainsaw bar and chain running hot and smoking?
    • K
      Kimberly RogersAug 5, 2025
      The bar and chain of your Oleo-Mac Chainsaw might be running hot and smoking due to several reasons: * The chain oil tank may be empty; it should be filled every time you fill the fuel tank. * The chain tension might be too tight; adjust the chain tension according to the instructions. * There might be an oiler malfunction. Run the saw at full throttle for 15 to 30 seconds, then stop it and check for oil dripping from the bar tip guard and guide bar. If there's no oil, contact a Servicing Dealer.
  • J
    John GuerreroAug 10, 2025
    What to do if my Oleo-Mac Chainsaw engine does not reach full speed and emits excessive smoke?
    • T
      Tom GarciaAug 10, 2025
      If your Oleo-Mac Chainsaw engine isn't reaching full speed and is emitting excessive smoke, consider the following: 1. Check the oil fuel mixture. Use fresh fuel and the correct 2-cycle oil mix. 2. The air filter might be dirty. Clean it following the instructions in the Maintenance- Air Filter Section. 3. The carburetor may require adjustment. Contact a Servicing Dealer for carburetor adjustment.
  • P
    Paul WilliamsAug 16, 2025
    Why does my Oleo-Mac GSH 400 Chainsaw engine start but will not accelerate properly?
    • J
      jeffreybeckAug 16, 2025
      If your Oleo-Mac Chainsaw engine starts but won't accelerate properly or run well at high speed, the carburetor likely requires adjustment. Contact a Servicing Dealer for carburetor adjustment.
  • P
    Paul MezaAug 22, 2025
    What to do if my Oleo-Mac GSH 400 Chainsaw engine starts, runs and accelerates but will not idle?
    • K
      Katrina BeasleyAug 22, 2025
      If your Oleo-Mac Chainsaw engine starts, runs, and accelerates but won't idle, turn the idle speed screw “T” clockwise to increase the idle speed. See Operation-Carburetor Adjustment.

Summary

Explanation of Symbols and Safety Warnings

Chain Saw Components

Safety Precautions

Fitting the Bar and Chain

Starting

Fueling

Details the correct procedures and precautions for refueling the chainsaw with fuel mixture.

Oil Filling and Chain Lubrication

Starting the Engine

Engine is Flooded

Describes troubleshooting steps for an engine that is flooded and won't start.

Stopping the Engine

Use

Ice Device System

Explains the function and use of the ice device system for cold weather operation.

Chain Brake

Details the operation and safety features of the chainsaw's chain brake system.

Checking Brake Operation

Procedures for verifying the correct functionality of the chain brake.

Prohibited Use

Precautions for the Work Area

Operating Instructions

Tree Felling

Specific instructions and safety advice for the process of felling trees.

Limbing

Bucking

Maintenance

Emissions Compliance

Details engine emissions control and compliance with regulations.

Chain Sharpening

Instructions on how to sharpen the chainsaw chain for optimal cutting performance.

Fuel Filter and Oil Pump

Maintenance procedures for the fuel filter and adjustment of the chain oil pump.

Engine and Spark Plug

Guidance on cleaning engine components and maintaining the spark plug.

Carburetor and Chain Brake

Procedures for adjusting the carburetor and maintaining the chain brake mechanism.

Muffler

Information regarding the chainsaw's muffler, including its catalytic converter and heat.

Extra Maintenance Advisable

Recommendations for additional maintenance services by qualified technicians.

Transportation

Guidelines for safely transporting the chainsaw, ensuring it is secured.

Maintenance Chart

Storage

Environmental Protection

Guidance on environmentally responsible disposal of oils, parts, and the machine itself.

Demolition and Disposal

Procedures for the safe and environmentally sound disposal of the chainsaw at its end of life.

Technical Data

Recommended Guide Bar and Chain Combinations

Lists the appropriate guide bar and chain types recommended for the chainsaw.

Declaration of Conformity

Warranty Certificate

Limited Warranty

Specifies the terms and duration of the limited warranty provided for the chainsaw.

Troubleshooting

Oleo-Mac GSH 400 Specifications

General IconGeneral
Engine Displacement38.9 cm³
Weight4.5 kg
Oil PumpAutomatic
Chain Pitch3/8"
Chain Gauge0.050"
Bar Length40 cm
ChainOregon

Related product manuals