Olimpia splendid Unico Air - Assembly, Connection, and Configuration; Air Ducts, Grids, and Unit Mounting; Electric Hook-up and Installation Options

w
couple the two
chains to the
large eyelet
of the spring.
Using one
hand,
grip
the
two chains connected
to the
grid.
Bend the external
grids
back,
gripping
them
with
your
free hand where they bend, and
insert
your
fingers inside the single
fins
(fig.
13).
lnsert
your
arm
into the
pipe
until
the
grid
protrudes
completely
outwards.
Reopen the
grid,
being careful
to keep
yourfingers
inside the
fins.
Turn the
grid
until the
fins are fully
horizontal and tilted
downwards.
Pull the
chain, tensioning
the spring, and
couple the chain
ring to the
pin
of the
inner flange through
which the
pipes
pass
(fig.
14)
Use
hand shears
to cut off
any excess chain
links.
[F
[F
A
IF
WARNING:
use exclusively
the
supplied
grids,
or
grids
with like characteristics.
2.3.5
Preparing the
holes on
the
machine
The unit
was built to
be
paired
with 162-mm.
2.3.6
Fitting the unit
on the
bracket
After having checked
that the
fixing bracket
is
properly
anchored to the
wall
and
that the suitable
preparatory
work
-
if required
-
has been carried
out
for
the
electrical connections
and
the condensate
drainage, the air-conditioner
can be
fixed to the wall.
Lift it
by
holding
it from the sides
of the
lower base
(see
fig.
15).
To facilitate
the operation
of fastening
it to the
bracket,
tilt it slightly toward
you.
To
make the electrical
connection
and
fasten the
drainpipe,
place
a wedge between
the air conditioner
and the
wall
(see
fig.
15).
When
you
have finished,
inspect carefully
to
make sure there
are no fissures at the
back of the air
conditioner
(the
insulating
gasket
must
fit firmly against
the wall)
particularly
in the zone
where air enters
and leaves the
machine.
2.3.7
Electric
hook-up
The appliance
is
fitted with a
power
cord with
plug (Y{ype
connection).
lf the socket is in
proximity
to the appliance,
simply
plug
it in.
A
Before connecting
the conditioner,
ensure
that:
-
The
power
supply
voltage
and frequency
values comply
with those
indicated on the
data
plate
of the appliance.
- The
power
supply line
is fitted with
an efficient
earth connection
that is appropriately
sized
for
the
maximum absorption
of the conditioner
(minimum
cross-section
of the cable
must be 1.5 mm'z)"
- The appliance
is
powered
exclusively through
a socket
that is compatible
with the
plug
supplied.
WARNING:
Any'replacement
of
the
power
cable
must be carried
out solely by Olimpia
Splendid
technical support
or by
similarly
qualified
personnel.
WARNING:
On
the
power
supply
line of the
appliance there
must be an adequate
omnipolar
disconnection
device
that
complies
with the
national installation
regulations.
lt is, however,
necessary to check
that the electrical
power
supply
is
equipped
with efficient
earthing
and
with adequate
protections
against overloading
and/or
short circuits
(a
type
10 AT
delayed
fuse or other
devices
with equivalent
functions are
recommended).
2.4
TOP/BOTTOM
INSTALLATION
CONFIGURATION
This
unit may
be installed
either at
the bottom
of the
wall
(adjacent to the floor) or at the
top
(adjacent
to the
ceiling). The
air
jet
can
be
modified to optimize
air distribution
and
room well-being
by changing the
position
of the
air outlet
flap.
31