To Next PageTo Next PageWhat to do if the bulb does not light on Olympus Microscope?
If the bulb does not light on your Olympus Microscope, first mount the designated bulb. If already mounted, replace the bulb as it may be burnt out. Ensure the power cord is properly connected.
How to fix field of view if it is obscured on Olympus Microscope?
If the field of view is obscured or not evenly illuminated on your Olympus Microscope, ensure that the revolving nosepiece and dummy slider click properly into place. Also, check that the condenser is fully re-inserted without any tilt, and the field iris diaphragm is correctly centered and opened to an optimum stop position. Clean any dirt or dust from the objective, eyepieces, condenser, or light exit glass.
Why is the image blurry on my Olympus CX41?
If visibility is poor, the image isn't sharp, contrast is poor, or details are indistinct on your Olympus Microscope, ensure the objective is correctly engaged in the light path by making sure the revolving nosepiece clicks into place. Clean any dirt or dust from the front lens of the objective and specimen. If using an oil immersion objective, use the specified immersion oil, ensuring it's free of bubbles.
Why is one side of the image blurred on my Olympus CX41?
If one side of the image is blurred or the image seems to waver on your Olympus Microscope, ensure the objective is correctly engaged in the light path by confirming the revolving nosepiece clicks into place correctly. Also, make sure the specimen is correctly mounted on the stage and secured with the specimen holder.
Why does the image blur when moving the specimen on my Olympus CX41?
If the image blurs as you move the specimen on your Olympus Microscope, ensure the specimen is correctly positioned on the stage. Mount the specimen correctly by applying it on the stage surface and inserting it below the specimen holder.
How to fix coarse adjustment knob if it is hard to turn on Olympus Microscope?
If the coarse adjustment knob is hard to turn on your Olympus Microscope, loosen the tension adjustment ring. Additionally, unlock the pre-focusing lever if you are trying to raise the stage with the coarse adjustment knob while the lever is locked.
What to do if the objective lens hits the slide on Olympus Microscope?
If the front lens of a high power objective comes into contact with the specimen when it is engaged after a low-power objective on your Olympus Microscope, ensure the specimen is mounted correctly. Also, use a 0.17 mm thick cover glass.
How to prevent image diffraction on Olympus CX41 Microscope?
If the image shows diffraction on your Olympus Microscope, adjust the condenser height position. Also, open the aperture iris diaphragm.
Why does the bulb burn out so quickly on my Olympus CX41?
If the bulb burns out almost immediately on your Olympus Microscope, use the correct bulb type.
Why is the field of view different for each eye on my Olympus Microscope?
If the field of view of one eye does not match that of the other on your Olympus Microscope, adjust the interpupillary distance and diopter. Ensure that the same eyepieces are used on both the left and right sides. Try looking at the overall field before concentrating on the specimen range. You may also find it helpful to look up and into the distance for a moment before looking back into the microscope.
General| Type | Biological Microscope |
|---|---|
| Optical System | UIS2 Optical System |
| Objectives | Plan Achromat objectives (4x, 10x, 40x, 100x Oil) |
| Nosepiece | Revolving nosepiece for 4 objectives |
| Power Supply | AC 100-240V, 50/60Hz |
| Illumination | 6V/30W halogen bulb |
| Focusing | Coaxial coarse and fine focusing knobs |
| Stage | Fixed stage with specimen holder |
| Eyepiece Tube | Binocular or Trinocular |
| Condenser | Abbe condenser, NA 1.25, with iris diaphragm |
| Eyepiece | 10x/20mm high eyepoint, widefield (depending on model) |
