Olympus WS-803 - Essential Setup Procedures (QSG); Battery Insertion and Type Setting; USB Charging and Power Management; Setting Time and Date

This recorder can be used
with
either
a Ni-MH rechargeable
battery
or
AAA
alkaline
battery.
U
For WS-803, WS-802:
•
When charging
the
recorder, make
sure
that
the
supplied
Ni-MH
rechargeable
battery
(BR404)
is
in
place.
U
For WS-801:
This recorder
cannot
charge
the
rechargeable battery.
1
Lightly
press
down
on
the
arrow
and
slide
the
battery
cover
open.
2
Insert
the
battery,
observing
the(±)
and
e
polarities.
3
Close
the
battery
cover
completely
by
pressing
down
at@,
then
sliding
the
cover
towards@.
Select
the
battery
type
to
match
the
battery
you are using.
1
Replace
the
battery
and
turn
on
the
recorder.
2
Press
the+
or-
button
to
change
the
setting.
[Ni-MH]
(13@]):
Select
when
using
the
Olympus
Ni-MH rechargeable
battery
(BR404).
[Alkaline]
(lll@j):
Select
when
using
an
alkaline
battery.
3
Press
the~
OK
button
to
complete
the
setting.
•
If
the
"Hour"
indicator
flashes
in
the
display,
see
"Setting
the
time
and
date
[Time &
Date]".
U
For
WS-803,
WS-802:
Do
not
charge a
primary
battery
such
as
an
alkaline
or
lithium
battery.
It
may
cause
battery
leakage
or
heating,
which
may
cause
the
recorder
to
malfunction.
1
Boot
the
PC.
2
Slide
the
USB
connector
slide
lever
in
the
direction
indicated
by
the
arrow
so
that
the
USB
connector
protrudes
from
the
recorder.
3
Make
sure
that
the
recorder
is
in
stop
mode,
and
connect
to
the
PC's
USB
port.
4
Press
the~
OK
button
to
start
charging.
• While
[Press
OK
to
start
charging]
is
flashing,
press
the
.,..OK
button.
S
Charging
is
completed
when
the
battery
indicator
shows
UOO.
Note:
• Insert
the
supplied
rechargeable
battery
and set
[Battery]
to
[Ni-MH].
If
[Battery]
is
set
to
[Alkaline],
you cannot recharge.
When
the
recorder
is
not
being
used,
turn
the
power
off
to
reduce
battery
consumption.
Existing data,
mode
settings, and
clock
settings are
not
lost
when
the
power
is
turned
off.
Turning
on
the
power:
While
the
recorder
is
turned
off,
slide
the
POWER/HOLD
switch in
the
direction
ofthe
arrow.
Turning
off
the
power:
Slide
the
POWER/HOLD
switch in
the
direction
of
the
arrow, and
hold
it
for
0.5 seconds
or
longer.
Power
save
mode:
If
the
recorder
is
on
but
is
not
used
for
10
minutes
or
longer
(default),
the
display
shuts
off
and
the
recorder
goes
into
power
save mode.
•
To
exit
power
save mode, press any
button
.
When you use
the
recorder
for
the
first
time,
or
when
the
battery
is
inserted
after
the
recorder has
not
been used
for
a
long
time,
[Set
time
& date]
will
appear. When
"Hour"
is
flashing,
conduct
setup
from
Step
6.
1
While
the
recorder
is
in
stop
mode,
press
the
MENU
button.
2
Press
the+
or-
button
to
select
[Device Menu]
tab.
•
You
can change
the
menu
display
by
moving
the
settings
tab
cursor.
3
Press
the~
OK
button
to
move
the
cursor
to
the
item
you
want
to
set.
4
Press
the
+
or-
button
to
select
[Time
&
Date].
S
Press
the~
OK
button
.
• "Hour"
flashes on
the
display,
indicating
the
start
of
the
Time
and Date setup process.
6
Press
the~
or~
button
to
select
the
item
you
want
to
set.
7
Press
the+
or-
button
to
change
the
value.
• Follow
the
same steps
by
pressing
the~
or~
button
to
select
the
next
item,
and pressing
the+
or-
button
to
change
the
value.
•
You
can
select
between
12
and
24
hour
display
by
pressing
the
LIST
button
while
setting
the
hour
and
minute.
•
You
can
select
the
order
of
"Month", "Day"
and
"Year"
by
pressing
the
LIST
button
while
setting
these items.
8
Press
the~
OK
button
to
complete
the
setting.
•
The
clock
will
start
from
the
set
date and time.
Press
the
.,..OK
button
when
you
want
the
clock
to
start.
9
Press
the
STOP
(•)
button
to
close
the
menu
screen.
I
EN
9