Omron E5CC-RX2ABM-000

Questions and Answers

H
hamiltonamyAug 18, 2025
Why is my Omron Temperature Controller overshooting, undershooting, or hunting?
- J
  Jorge FuentesAug 18, 2025
  If your Omron Temperature Controller is showing overshooting, undershooting or hunting, it could be due to several reasons. First, if ON/OFF control is enabled, select PID control and perform autotuning. Second, if the control period is too long compared to the temperature's rise and fall speed, shorten the control period. Third, unsuitable PID constants can cause this issue; execute AT (autotuning) or manually set appropriate PID constants. Finally, an HS alarm operation fault may be the cause; use breeder resistance if leakage current is the problem and investigate errors detected by the HS alarm function.
M
Margaret KellyAug 23, 2025
What to do if Omron E5CC-RX2ABM-000 Temperature Controller shows a large temperature error (S.Err)?
- A
  Andrew HowardAug 23, 2025
  If your Omron Temperature Controller displays a large temperature error or an input error (S.Err), check the sensor type and reset the input type correctly. Also, ensure the thermometer is installed properly, checking its installation location and polarity. Make sure that the connected device is not faulty.
D
Dana OneillAug 26, 2025
Why is the temperature not rising in my Omron E5CC-RX2ABM-000 Temperature Controller?
- L
  Leah LeeAug 26, 2025
  If the temperature is not rising on your Omron Temperature Controller, first, ensure that the specified operation (forward or reverse) is suitable for the required control. Check for heater burnout or deterioration and verify the heater's heating capacity is sufficient. Also, check if a cooling system is in operation. Finally, ensure that any peripheral devices with heat prevention are set to a value higher than the set temperature of the Digital Controller.
J
Jamie RayAug 28, 2025
Why won't my Omron E5CC-RX2ABM-000 Temperature Controller operate?
- N
  Nicholas MorganAug 28, 2025
  If your Omron Temperature Controller will not operate, ensure the Run/Reset parameter is set to Run. Check whether the thermometer has burnt out or short-circuited. Ensure thermometer lead wires and power lines are in separate conduits, or wired using a more direct path. The connection between the Digital Controller and thermocouple should use the thermocouple’s lead wires directly, or compensating conductors suitable for the thermocouple. Verify the thermometer's installation location is suitable and set a suitable input shift, or set the input shift value to 0.0 if not required.
J
Joseph DelgadoAug 30, 2025
Why won't the output turn on in my Omron Temperature Controller?
- E
  Elizabeth RomeroAug 30, 2025
  If the output of your Omron Temperature Controller will not turn ON, ensure the Run/Reset parameter is set to Run. Select either forward or reverse operation depending on the required control. Set a suitable value for the hysteresis. Supply the specified power from the terminals, as the output will not turn ON while the Digital Controller is being operated with power supplied through the USB-Serial Conversion Cable.
N
Nicholas HendersonSep 2, 2025
Why is the control unstable on my Omron E5CC-RX2ABM-000 Temperature Controller?
- C
  cmedinaSep 2, 2025
  If the control is unstable on your Omron Temperature Controller, retighten terminal screws to a torque of 0.43 to 0.58 N·m. If the internal components have reached the end of their service life, replace the Digital Controller and all other Digital Controllers purchased in the same time period.
J
Jeremy DanielsSep 4, 2025
How to unlock Omron E5CC-RX2ABM-000 Temperature Controller keys?
- D
  Donald PhamSep 4, 2025
  If the keys on your Omron Temperature Controller will not operate, turn OFF setting change protect.
A
alan88Sep 7, 2025
Why can't I shift levels on my Omron Temperature Controller?
- Z
  zmunozSep 7, 2025
  If you cannot shift levels on your Omron Temperature Controller, set the operation/adjustment protect, initial setting/communications protect, and setting change protect values as required.
B
Bryan DiazSep 9, 2025
Why isn't the SP changing as programmed on my Omron Temperature Controller?
- A
  Adam HarrisSep 9, 2025
  If the SP (Set Point) does not change as programmed on your Omron Temperature Controller, set Program SP Mode.
A
Anne BowersSep 12, 2025
Why isn't the segment advancing on my Omron E5CC-RX2ABM-000 Temperature Controller?
- E
  Elizabeth BarnesSep 12, 2025
  If the segment does not advance on your Omron Temperature Controller, set the wait band correctly.

Omron E5CC-RX2ABM-000 Specifications

General

Type	Digital Temperature Controller
Model	E5CC-RX2ABM-000
Power Supply	100 to 240 VAC
Size	48 x 48 mm
Number of Outputs	2
Control Output 1	Relay
Mounting Method	Panel Mount
Number of Control Outputs	1
Setting Resolution	0.1 °C
Protection Rating	IP66
Input Type	Thermocouple, RTD
Output Type	Relay, Voltage
Display Type	LCD
Control Method	PID
Alarm Output	Relay