Omron E5CN-H Communications Manual

Com Data for CompoWay/F
3.1 Variable Area (Setting Range) List
3-3
Note: The alarm function can also be used in Controllers without alarm output terminals. In this case, confirm alarm occurrences
via the status data.
Note 1: The parameter for the currently selected bank will be accessed.
Note 2: Not displayed on the Controller display when Alarm 3 is not assigned to an output.
Note 3: The parameter for the currently selected PID set will be accessed. For setup area 1, however, the currently selected PID
set is fixed at PID1.
Variable
type
Address Parameter name Setting (monitor) value Level
C1 (81) 0000 Operation/Adjustment Protect H'00000000 (0): No restrictions in operation and adjustment levels
H'00000001 (1): Move to adjustment level is prohibited.
H'00000002 (2): Display and change of only “PV” and “PV/SP” parame-
ters is allowed.
H'00000003 (3): Display of only “PV” and “PV/SP” parameters is allowed.
Protect
C1 (81) 0001 Initial Setting/Communications Protect H'00000000 (0): Move to initial setting/communications setting level is
allowed. (Move to advanced function setting level is dis-
played.)
H'00000001 (1): Move to initial setting/communications setting level is
allowed. (Move to advanced function setting level is not
displayed.)
H'00000002 (2): Move to initial setting/communications setting level is
prohibited.
C1 (81) 0002 Setting Change Protect H'00000000 (0): OFF (Changing of setup on Controller display is allowed.)
H'00000001 (1): ON (Changing of setup on Controller display is prohib-
ited.)
C1 (81) 0003 Set Point (See note 1.) SP lower limit to SP upper limit Operation
C1 (81) 0004 Alarm Value 1 (See note 1.) H'FFFFB1E1 to H'00007E90 (
−19999 to 32400)
C1 (81) 0005 Alarm Value Upper Limit 1 (See note 1.) H'FFFFB1E1 to H'00007E90 (
−19999 to 32400)
C1 (81) 0006 Alarm Value Lower Limit 1(See note 1.) H'FFFFB1E1 to H'00007E90 (
−19999 to 32400)
C1 (81) 0007 Alarm Value 2 (See note 1.) H'FFFFB1E1 to H'00007E90 (
−19999 to 32400)
C1 (81) 0008 Alarm Value Upper Limit 2 (See note 1.) H'FFFFB1E1 to H'00007E90 (
−19999 to 32400)
C1 (81) 0009 Alarm Value Lower Limit 2 (See note 1.) H'FFFFB1E1 to H'00007E90 (
−19999 to 32400)
C1 (81) 000A Alarm Value 3 (See notes 1 and 2.) H'FFFFB1E1 to H'00007E90 (
−19999 to 32400)
C1 (81) 000B Alarm Value Upper Limit 3
(See notes 1 and 2.)
H'FFFFB1E1 to H'00007E90 (
−19999 to 32400)
C1 (81) 000C Alarm Value Lower Limit 3
(See notes 1 and 2.)
H'FFFFB1E1 to H'00007E90 (
−19999 to 32400)
C1 (81) 000D Heater Burnout Detection 1 H'00000000 to H'000001F4 (0.0 to 50.0) Adjustment
C1 (81) 0012 Temperature Input Shift H'FFFFB1E1 to H'00007E90 (
−199.99 to 324.00)
C1 (81) 0013 Upper Limit Temperature Input Shift
Value
H'FFFFB1E1 to H'00007E90 (
−199.99 to 324.00)
C1 (81) 0014 Lower Limit Temperature Input Shift
Value
H'FFFFB1E1 to H'00007E90 (
−199.99 to 324.00)
C1 (81) 0015 Proportional Band (See note 3.) Temperature: H'00000001 to H'00007E90 (0.1 to 3240.0)
Analog: H'00000001 to H'0000270F (0.1 to 999.9)
C1 (81) 0016 Integral Time (See note 3.) Standard, heating/cooling, positional proportional (closed):
H'00000000 to H'00007E90 (0.0 to 3240.0)
Positional proportional (floating):
H'00000001 to H'00007E90 (0.1 to 3240.0)
C1 (81) 0017 Derivative Time (See note 3.) H'00000000 to H'00007E90 (0.0 to 3240.0)
C1 (81) 0018 Cooling Coefficient (See note 3.) H'00000001 to H'0000270F (0.01 to 99.99)
C1 (81) 0019 Dead Band Temperature: H'FFFFB1E1 to H'00007E90 (
−1999.9 to 3240.0)
Analog: H'FFFFF831 to H'0000270F (
−199.9 to 999.9)
C1 (81) 001A Manual Reset Value H'00000000 to H'000003E8 (0.0 to 100.0)
C1 (81) 001B Hysteresis (Heating) Temperature: H'00000001 to H'00007E90 (0.1 to 3240.0)
Analog: H'00000001 to H'0000270F (0.1 to 999.9)
C1 (81) 001C Hysteresis (Cooling) Temperature: H'00000001 to H'00007E90 (0.1 to 3240.0)
Analog: H'00000001 to H'0000270F (0.1 to 999.9)
C1 (81) 001D Heater Burnout Detection 2 H'00000000 to H'000001F4 (0.0 to 50.0)
C1 (81) 001E HS Alarm 1 H'00000000 to H'000001F4 (0.0 to 50.0)
C1 (81) 001F HS Alarm 2 H'00000000 to H'000001F4 (0.0 to 50.0)
C1 (81) 0020 Soak Time (See note 1.) H'00000000 to H'0000270F (0 to 9999)
C1 (81) 0021 Wait Band (See note 1.) H'00000000(0): OFF
Temperature: H'00000001 to H'00007E90 (0.1 to 3240.0)
Analog: H'00000001 to H'0000270F (0.01 to 99.99)

Omron E5CN-H Specifications

General

Brand	Omron
Model	E5CN-H
Category	Controller
Language	English