Onkyo A-R700

A-R700
FRONT PANEL FACILITLES
)
oy 2 me} a 6B)
2 EO MERTA wTESRATIT sree per RRL
adeh RET ERA -AS = SUMP EMENCE “eerearoimaes
Power Button (POWER)
Press the POWER button to turn on the power.
Press this button to switch the on/off status of the power supply
and the AC outlets on the rear panel. Power can also be turned
on by using the remote control POWER button, An orange band
over the power button indicates power is on.
Remote Control Sensor
This receives signals sent from RC-180S remote control
transmitter.
MUTING —o°o/STAND-BY Indicator
This indicator is iluminated and the unit enters STAND-BY
mode, when the unit is plugged in. The power is turned ON/OFF
by pressing the POWER button or remote control transmitter
POWER button.
- The indicator blinks on and off and the sound is muted when
the remote control transmitter MUTING —ce button is pressed.
Muting Switch (MUTING)
When this switch is set to the ~20dB position, the volume level
is reduced to one-tenth of the level set by the VOLUME control.
Mode Selector Switch (MODE)
STEREO { BL): Position for normal stereo listening.
MONO (=) =: Both right and left channel signals are sent
to each speaker. Position for listening to
monaural recordings or when adjusting the
BALANCE control. .
Volume Contro! Knob (VOLUME)
This controls volume. Turning it clockwise increases volume.
When controlling with the remote contrai transmitter, pressing
“UP” and “DOWN” increases and decreases volume respec-
tively. This control employs the system of simultaneous changes
in volume and boost characteristics.
Input Selector Buttons and Indicators (INPUT SELEC-
TOR) ;
These buttons are used to select the desired program source.
Pressing one releases the previously pressed button, so be sure
to press only one button at atime. An indicator shows which
program has been selected.
TAPE-2
TAPE-1
: Tape deck connected to the TAPE-2 jacks.
: Tape deck connected to the TAPE-1 jacks.
TUNER—-Tuner-connected to the TUNER jacks
cD : Compact disc player connected to the CD jacks.
— 29 —
LOWS IMPEDANCE OMVE
OSCRITE asd IF
DAT : Tape deck connected to the DAT jacks.
AUX-1, 2 : Additional audio component connected to the
AUX-1 or 2 jacks.
PHONO: Turntable connected to the PHONO jacks.
Speaker Selector Switch (SPEAKERS)
This unit can drive two different speaker systems at once. Use
this selector to activate either or both speaker systems con-
nected to the rear panel speaker terminals. In the OFF position,
sound is heard only through the headphones.
OFF : All speakers off—only headphones operate.
A : Speaneis A
B : Speakers B
A+B : Both speaker systems A and B.
Headphone Jack (PHONES)
Stereo headphones with a standard binaural plug can be
connected here.
Bass Control Knob (BASS)
Turn right to boost or left to attenuate bass. In the DEFEAT
position, the BASS tone control circuitry is completaly by-
passed. =
Treble Control Knob (TREBLE)
Turn right to boost or left to attenuate treble. In the DEFEAT
position, the TREBLE tone control circuitry is completely by-
passed. When turned to the extreme left (-10), the TREBLE
control acts as a high cut filter to eliminate scratches; hissing
and other high frequency noise.
About the Variable Tone Boosting System
This unit is designed to gradually reduce the effect of the tone
controls {BASS and TREBLE) when the VOLUME exceeds a
certain level. The variable boosting system gradually reduces
the boosting effect of the BASS and TREBLE controls when
one or both of these controis is turned beyond (to the right of}
the center defeat position and the VOLUME comtrol js turned
beyond the center position. When the VOLUME is turned all the
way up, the frequency response wiil be flat again. The VOLUME
settings below the center pasition have no effect on the DIRECT
TONE controls. Also, BASS and TREBLE control settings below
(to the !eft of) the center DEFEAT position are not altered by
the volume level.