Onkyo HT-R695 User Manual

12
> Specifications > Settings > Listening Modes > Playback Function > Basic Manual
Troubleshooting | Appendix
Setting Item Default Value Setting Details
Surr Back Right (0 dB) Select a value between "－12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
•
The setting cannot be changed if "Zone 2" is set
in "Configuration" - "Zone Speaker" and Zone 2
is on.
Surr Back Left (0 dB) Select a value between "－12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
•
The setting cannot be changed if "Zone 2" is set
in "Configuration" - "Zone Speaker" and Zone 2
is on.
Surround Left 0 dB Select a value between "－12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
Subwoofer 0 dB Select a value between "－15 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
■ 5� Dolby Enabled Speaker
Setting Item Default Value Setting Details
Dolby Enabled
Speaker to
Ceiling
6.0 ft/1.80 m Set the distance between the Dolby Enabled
Speaker and the ceiling. Select between "0.1
ft/0.03 m" to "15.0 ft/4.50 m" (0.1 ft/0.03 m units).
•
The unit of distance (ft/m) shown is the unit
selected for use in "Distance".
AccuReflex Off You can enhance the reflection effect of Dolby
Enabled Speakers from the ceiling.
"Off": Do not use this function
"On": Use this function
■ 6� Equalizer Settings
You can adjust the output volume of the range of each connected speaker. You can adjust
the volume of the different sound ranges for each of the speakers. You can set three
different equalizers in Preset 1 to 3. You can select up to five bands for the Subwoofer and
nine bands for all other speakers.
Setting Item Default Value Setting Details
Front 0 dB After selecting the speaker frequency from
between 25 Hz" and "16 kHz" with the cursors
/
, adjust the volume of that frequency between
"－6 dB" and "＋6 dB" with / .
Center 0 dB After selecting the speaker frequency from
between 25 Hz" and "16 kHz" with the cursors
/
, adjust the volume of that frequency between
"－6 dB" and "＋6 dB" with / .
Height 0 dB After selecting the speaker frequency from
between 25 Hz" and "16 kHz" with the cursors
/
, adjust the volume of that frequency between
"－6 dB" and "＋6 dB" with / .
•
This cannot be selected if "Zone 2" is set in
"Configuration" - "Zone Speaker" and Zone 2 is on.
Surround 0 dB After selecting the speaker frequency from
between 25 Hz" and "16 kHz" with the cursors
/
, adjust the volume of that frequency between
"－6 dB" and "＋6 dB" with / .
Surround Back (0 dB) After selecting the speaker frequency from
between 25 Hz" and "16 kHz" with the cursors
/
, adjust the volume of that frequency between
"－6 dB" and "＋6 dB" with / .
•
This cannot be selected if "Zone 2" is set in
"Configuration" - "Zone Speaker" and Zone 2 is on.
Subwoofer 0 dB After selecting the speaker frequency from
between 25 Hz" and "160 Hz" with the cursors
/
, adjust the volume of that frequency between
"－6 dB" and "＋6 dB" with / .
•
This cannot be selected if "No" is set in
"Configuration" - "Subwoofer".
•
The result may not be as expected depending on the input source and listening mode setting.

Onkyo HT-R695 Specifications

General

Brand	Onkyo
Model	HT-R695
Category	Receiver
Language	English