Onkyo NS-6130 User Manual

25
> Before Start > Part Names > Install > Initial Setup > Playback
Supplementary information | Advanced Setup |Others
E
N
Updating via USB
0 Prepare a 128 MB or larger USB storage device. FAT16
or FAT32 file system format.
0 Delete any data stored on the USB storage device.
0 Turn off the controller component (PC etc.) connected to
the network.
0 Stop any playing Internet radio, USB storage device, or
server content.
0 Some USB storage devices may take long to load, may
not be loaded correctly, or may not be correctly fed
depending on the device or their content.
0 We will not be liable whatsoever for any loss or damage
of data, or storage failure arising from the use of the USB
storage device with this unit. Thank you for your
understanding.
1. Connect the USB storage device to your PC.
2. Download the firmware file from our company’s website
to your PC and unzip.
Firmware files are named in the following way:
ONKNAP ＊＊＊＊ _ ＊＊＊＊＊＊＊＊＊＊＊＊＊＊ _ ＊＊＊ .zip
Unzip the file on your PC. The number of unzipped files
and folders varies depending on the model.
3. Copy all unzipped files and folders to the root folder of
the USB storage device.
0 Make sure to copy the unzipped files.
4. Connect the USB storage device to the USB port of this
unit.
0 If you connect a USB hard disk drive to the USB port of
the unit, we recommend that you use its AC adapter to
power it.
0 If the USB storage device has been partitioned, each
section will be treated as an independent device.
5. "Network" is displayed on the display when SETUP on
the remote controller is pressed.
6. Press / and ENTER to select "Update" - "via USB" in
order.
0 "Update" is not displayed if there are no firmware
updates.
7. Press ENTER to start the firmware update.
0 "Completed" is displayed when the update is
complete.
8. Press ÍON/STANDBY on the main unit to switch the unit
to standby. The process is completed and your firmware
is updated to the latest version.
9. Remove the USB storage device from this unit.
If an error message is displayed: When an error occurs,
" ＊ - ＊＊ Error!" is displayed on the display of this unit.
Check the following:
0 ＊ -01, ＊ -10: USB storage device not found. Check
whether the USB storage device or USB cable is
correctly inserted to the USB port of this unit.
Connect the USB storage device to an external power
source if it has its own power supply.
0 ＊ -05, ＊ -13, ＊ -20, ＊ -21: The firmware file is not
present in the root folder of the USB storage device, or
the firmware file is for another model. Retry from the
download of the firmware file.
0 Others: Disconnect then reconnect the AC power cord,
then repeat from the beginning.
Network
Update

Onkyo NS-6130 Specifications

General

Receiver type	Surround
Frequency range	4 - 70000 Hz
Audio output channels	- channels
Signal-to-Noise Ratio (SNR)	112 dB
Total Harmonic Distortion (THD)	0.002 %
Power output per channel (20-20KHz@8 Ohm)	- W
HDMI in	0
USB ports quantity	2
Ethernet LAN (RJ-45) ports	1
Connectivity technology	Wired & Wireless
Speakers connectivity type	RCA
Bluetooth	No
Ethernet LAN	Yes
Supported radio bands	-
Product color	Black
Audio formats supported	AAC, AIFF, FLAC, MP3
Package depth	388 mm
Package width	540 mm
Package height	210 mm
Package weight	5600 g
Cables included	AC
AC input voltage	220 - 240 V
AC input frequency	50 Hz
Power consumption (typical)	22 W

Weight and Dimensions

Depth	317 mm
Width	435 mm
Height	100 mm
Weight	3500 g