Onkyo NS-6170 User Manual

> Before Start > Part Names > Install > Initial Setup > Playback
Supplementary information | Advanced Setup |Others
25
E
N
Network
∫ Connection
Select the type connection to the network.
Select the item with / on the remote controller and press ENTER.
"Wi-Fi": To connect via wireless LAN
"Wired" (Default Value): To connect via wired LAN
Perform "Wi-Fi Setup" if you select "Wi-Fi".
∫ Wi-Fi Setup
Make Wi-Fi connection settings. (P10)
This can be set only when "Wi-Fi" is selected in "Connection".
0 You can make Wi-Fi connection settings using a web browser on a computer. For details,
refer to “Web Setup” (P27).
∫ DHCP
Select the item with / on the remote controller and press ENTER .
"On" (Default Value): Auto configuration by DHCP
"Off": Manual configuration without DHCP
If selecting "Off", you must set "IP Address", "Subnet Mask", "Gateway", and "DNS"
manually.
∫ IP Address
Displays/Sets the IP address.
∫ Subnet Mask
Displays/Sets the subnet mask.
∫ Gateway
Displays/Sets the gateway.
∫ DNS
Displays/Sets the primary DNS server.
∫ Proxy URL
Displays/Sets the proxy server URL.
∫ Proxy Port
Displays/Sets the proxy server port number when you enter "Proxy URL".
∫ Friendly Name
Change the device name for this unit which is shown on other devices connected to the
network to an easily recognized name. You can input up to 31 characters. For details on how
to enter text, refer to "Entering text" (P22).
∫ AirPlay PW
You can set a password of up to 31 characters so that only registered users can use AirPlay.
For details on how to enter text, refer to "Entering text" (P22).
∫ Network Check
You can check the network connection. The confirmation results are displayed when you
press ENTER.
Option
∫ PWR Setting
Auto Standby This setting places the unit on standby automatically after 20
minutes of inactivity without any audio input.
"On" (Default Value): The unit will automatically enter standby
mode.
"Off ": The unit will not automatically enter standby mode.
NET Stby
When this feature is turned "On", you can turn on the power of the
unit via the network using an application that can control this unit
.
Select the item with / on the remote controller and press
ENTER.
0 Setting to "On" (Default Value) increases the power
consumption even when the unit is on standby.
0 "NET Stby", which suppresses power consumption, may be
disabled when the network connection is lost.

Onkyo NS-6170 Specifications

General

Housing material	Aluminum
Control type	Buttons, Rotary
Package depth	388 mm
Package width	540 mm
Package height	210 mm
Receiver type	stereo
Frequency range	4 - 70000 Hz
Output impedance	75/470 Ω
Dynamic range (1kHz)	114 dB
Audio output channels	2.0 channels
Audio A/D Converter (ADC)	24-bit/192kHz
Signal-to-Noise Ratio (SNR)	115 dB
Total Harmonic Distortion (THD)	0.002 %
Power output per channel (20-20KHz@8 Ohm)	- W
Display	VFD
Platform	Android, iOS
Package type	Box
Apple docking	No
PC connection	RJ-45
Product color	Silver
Audio decoders	Not supported
Volume control	Digital
Number of products included	1 pc(s)
Multi-Room Streaming (MRS) support	Yes
HDMI in	0
Remote (IR) input	2
Ethernet LAN (RJ-45) ports	1
Connectivity technology	Wired & Wireless
Speakers connectivity type	RCA
Audio formats supported	AAC, AIFF, DSD, FLAC, MP3, RA-Lossless, WAV, WMA
Supported radio bands	DAB, DAB+, FM
Preset stations quantity	40
Internet radio services supported	Deezer, Spotify, Tidal, TuneIn
AC input voltage	220 - 240 V
AC input frequency	50 Hz
Power consumption (typical)	37 W
Certification	CE, WEEE
Package weight	6800 g
Cables included	AC

Weight and Dimensions

Depth	317 mm
Width	435 mm
Height	100 mm
Weight	4500 g