Onkyo TX-NR1008 Firmware Update

1
En
Firmware Update for TX-NR708/808/1008 and
HT-RC270
There are the following methods to update the firmware: via network and via USB storage.
Please choose either one that suits your condition. Before you start, carefully read the
update procedure. It will take about 30 minutes to update the firmware.
■Update via network
You need a wired Internet connection to update the firmware.
For the update procedure, please refer to “Updating the Firmware via Network” (➔ 2).
■Update via USB storage
Please prepare a USB storage device such as a USB flash memory stick. You need at
least 32 MB of available space to update the firmware.
For the update procedure, please refer to “Updating the Firmware via USB” (➔ 5).
Precautions:
• Check the network connection before update.
• Do not touch the cable or any other device connected to the AV receiver during updating process.
• Do not access the AV receiver from PC during updating process.
• Do not shutdown the power of the AV receiver while update.
• The storage media in the USB card reader may not work.
• If the storage device has been partitioned, each section will be treated as an independent device.
• If the USB mass storage device contains a lot of data, the AV receiver may take a while to read it.
• Operation with all USB mass storage devices including the ability to power them is not guaranteed.
• Onkyo accepts no responsibility whatsoever for the loss or damage to data stored on a USB mass
storage device when that device is used with the AV receiver. Onkyo recommends that you back
up your important music files beforehand.
• If you connect a USB hard disk drive to the USB port, Onkyo recommends that you use its AC
adapter to power it.
• USB hubs and USB devices with hub functions are not supported. Do not connect your USB mass
storage device via a USB hub.
• USB mass storage devices with security functions are not supported.
Limitation of liability
The program and accompanying online documentation are furnished to you for use at your own
risk. Onkyo will not be liable and you will have no remedy for damages for any claim of any kind
whatsoever concerning your use of the program or the accompanying online documentation,
regardless of legal theory, and whether arising in tort or contract. In no event will Onkyo be liable
to you or any third party for any special, indirect, incidental, or consequential damages of any kind,
including, but not limited to, compensation, reimbursement or damages on account of the loss of
present or prospective profits, loss of data, or for any other reason whatsoever.

Onkyo TX-NR1008 Specifications

Power

power output front L/R	180 W/Ch (6 Ω, 1 kHz, 1 channel driven, IEC)
power output center	180 W (6 Ω, 1 kHz, 1 channel driven, IEC)
power output surround L/R	180 W/Ch (6 Ω, 1 kHz, 1 channel driven, IEC)
power output surround back L/R	180 W/Ch (6 Ω, 1 kHz, 1 channel driven, IEC)
power output front high L/R, front wide L/R, or zone 2/3 L/R	180 W/Ch (6 Ω, 1 kHz, 1 channel driven, IEC)
dynamic power 3 Ω front	300 W
dynamic power 4 Ω front	250 W
dynamic power 8 Ω front	150 W
power consumption	830 W

Audio Specifications

thd (total harmonic distortion)	0.08% (Rated power)
damping factor	60 (Front, 1 kHz, 8 Ω)
input sensitivity and impedance line	200 mV/47 kΩ
input sensitivity and impedance phono mm	2.5 mV/47 kΩ
rated rca output level and impedance	200 mV/470 Ω (Pre out)
maximum rca output level and impedance	4.6 V/470 Ω (Pre out)
phono overload	70 mV (MM, 1 kHz, 0.5%)
frequency response	5 Hz–100 kHz/+1 dB, -3 dB (Direct mode)
tone control bass	±10 dB, 50 Hz
tone control treble	±10 dB, 20 kHz
signal-to-noise ratio line	110 dB (IHF-A)
signal-to-noise ratio phono	80 dB (IHF-A)
speaker impedance	4 Ω–16 Ω or 6 Ω–16 Ω

Video Specifications

input sensitivity/output level and impedance video	1.0 Vp–p/75 Ω (Component and S-Video Y)
input sensitivity/output level and impedance component pb/cb, pr/cr	0.7 Vp–p/75 Ω
input sensitivity/output level and impedance s-video c	0.25 Vp–p/75 Ω
input sensitivity/output level and impedance composite	1.0 Vp–p/75 Ω
component video frequency response	5 Hz–100 MHz/0 dB, -3 dB

Tuner Specifications

tuning frequency range fm	87.5 MHz–108 MHz
tuning frequency range am	522 kHz–1, 611 kHz
fm/am preset memory	40 stations

Weight and Dimensions

dimensions	435 x 198.5 x 435.5 mm
weight	18.7 kg
carton dimensions	587 x 337 x 553 mm
carton weight	23.5 kg