Onkyo TX-NR737 User Manual

Advanced Settings
33
LFE Level
Set the low-frequency effect (LFE) level of the Dolby Digital, DTS, Multichannel PCM, Dolby
TrueHD, DTS-HD Master Audio and DSD signals.
Setting item Default Value Setting Details
Dolby Digital 0dB Select the low-frequency effect (LFE) level of
each type of signal from "0dB" to "-ŬdB". If the
low-frequency effect sound is too strong, select
"-20dB" or "-ŬdB".
r This setting works on LFE channel volume of
Dolby Digital and Dolby Digital Plus sources.
DTS 0dB Select the low-frequency effect (LFE) level of
each type of signal from "0dB" to "-ŬdB". If the
low-frequency effect sound is too strong, select
"-20dB" or "-ŬdB".
r This setting works on LFE channel volume of
DTS and DTS-HD High Resolution sources.
Multich PCM 0dB Select the low-frequency effect (LFE) level of
each type of signal from "0dB" to "-ŬdB". If the
low-frequency effect sound is too strong, select
"-20dB" or "-ŬdB".
Dolby TrueHD 0dB Select the low-frequency effect (LFE) level of
each type of signal from "0dB" to "-ŬdB". If the
low-frequency effect sound is too strong, select
"-20dB" or "-ŬdB".
DTS-HD Master
Audio
0dB Select the low-frequency effect (LFE) level of
each type of signal from "0dB" to "-ŬdB". If the
low-frequency effect sound is too strong, select
"-20dB" or "-ŬdB".
DSD 0dB Select the low-frequency effect (LFE) level of
each type of signal from "0dB" to "-ŬdB". If the
low-frequency effect sound is too strong, select
"-20dB" or "-ŬdB".
r This setting works on LFE channel volume of
DSD (Super Audio CD) sources.
4.Source Setup
Adjust the volume level difference among the multiple devices connected to this unit,
rename an input selector, or adjust the image quality. The setting can be separately set to
each input selector button. When you select a desired input to check the video or audio,
start playback of the connected device.
AccuEQ Room Calibration
Setting item Default Value Setting Details
AccuEQ Room
Calibration
Off Enable/disable the sound field set in automatic
speaker setup
"On": Enable this function
"Off": Disable this function
r In the following cases, the setting cannot be
changed:
– Automatic speaker setup is not performed.
– Headphones are connected.
IntelliVolume
Setting item Default Value Setting Details
IntelliVolume 0dB Adjust the volume level difference between the
devices connected to the unit. Select a value
between "-12dB" to "+12dB".
Set a negative value if the volume of the target
device is larger than the others and a positive
value if smaller.
r This function is not effective in Zone 2/Zone
3.

Onkyo TX-NR737 Specifications

General

Receiver type	Surround
Frequency range	5 - 100000 Hz
Output impedance	6 Ω
Input sensitivity	200 mV
Audio output channels	7.2 channels
Signal-to-Noise Ratio (SNR)	106 dB
Total Harmonic Distortion (THD)	0.8 %
Dynamic power per channel (3 Ohm)	250 W
Dynamic power per channel (4 Ohm)	220 W
Dynamic power per channel (8 Ohm)	130 W
Power output per channel (20-20KHz@8 Ohm)	170 W
HDMI in	7
AC (power) in	Yes
Audio (L/R) in	6
Composite video in	3
Digital audio coaxial in	2
Digital audio optical in	1
Connectivity technology	Wired
Speakers connectivity type	-
Ethernet LAN	No
Bluetooth version	2.0+EDR
RDS features	PS, PTY, RT, TP
AM band range	522 - 1610 kHz
FM band range	87.5 - 108 MHz
Supported radio bands	AM, FM
Preset stations quantity	40
Display	LCD
Product color	Black
Audio decoders	Dolby TrueHD, DTS-HD, DTS-HD Master Audio
Damping factor	60
AC input voltage	220-240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.15 W
Power consumption (typical)	690 W

Weight and Dimensions

Depth	379 mm
Width	570 mm
Height	298 mm
Weight	11500 g