Onkyo TX-NR828 User Manual

Controlling Other Components
En-88
By pressing the REMOTE MODE button that’s been
programmed with the remote control code for your
Dock, you can control your iPod/iPhone in the Dock
with the buttons described further in this section.
See “Entering Remote Control Codes” for details on
entering a remote control code (➔ page 82).
See the Dock’s instruction manual for more
information.
RI Dock
• Set the RI Dock’s RI MODE switch to “HDD” or
“HDD/DOCK”.
• 8SOURCE may not work with a remote control
code (without u). In this case, make an u
connection and enter the remote control code 81993
(with u).
■ With the RI Control
Make an u connection and enter the remote control
code 81993 (with u).
• Set the AV receiver’s Input Display to “DOCK”
(➔ page 53).
■ Without the RI Control
You must enter the remote control code 82990 first
(➔ page 83).
■ u Dock operation
• With some iPod/iPhone models, generations and RI Docks,
certain buttons may not work as expected.
• For detailed operation of iPod/iPhone, please refer to the
instruction manual of the RI Dock.
*1
TOP MENU works as the mode button when used with
the DS-A2 RI Dock.
*2
DISPLAY turns on the backlight for a few seconds.
*3
This button does not turn the Onkyo DS-A2 or DS-A2X
RI Dock on or off. Also, your iPod/iPhone may not
respond the first time you press this button, in which case
you should press it again. This is because the remote
controller transmits the On and Standby commands
alternately, so if your iPod/iPhone is already on, it will
remain on when the remote controller transmits the On
command. Similarly, if your iPod/iPhone is already off, it
will remain off when the remote controller transmits the
Off command.
*4
Resume mode
With the Resume function, you can resume playback of
the song that was playing when you removed your
iPod/iPhone from the Onkyo DS-A2 RI Dock.
Controlling Your iPod/iPhone
b
a
k
j
i
d
e
f
c
g
h
Press the appropriate REMOTE
MODE button first.
Available buttons
a
TOP MENU
*1
e
DISPLAY
*2
b q/w/e/r, ENTER f 8SOURCE
*3
PLAYLIST e/r g
MUTING
c 1, 3, 2, 5, 4,
7, 6
h
ALBUM +/–
i VOL q/w
d
REPEAT
j
MENU
RANDOM
k
MODE
*4

Onkyo TX-NR828 Specifications

General

Impedance	6 Ω
Receiver type	Surround
Frequency range	20 - 20000 Hz
Input sensitivity	200 mV
Audio output channels	7.2 channels
Signal-to-Noise Ratio (SNR)	106 dB
Total Harmonic Distortion (THD)	0.08 %
Power output per channel (1KHz@6 Ohm)	180 W
Power output per channel (20-20KHz@8 Ohm)	- W
HDMI in	8
Digital audio coaxial in	3
Ethernet LAN (RJ-45) ports	1
Component video (YPbPr/YCbCr) in	2
Speakers connectivity type	-
Audio formats supported	AAC, FLAC, MP3, WAV, WMA
Ethernet LAN	Yes
AM band range	530 - 1710 kHz
FM band range	87.5 - 108 MHz
Supported radio bands	AM, FM
Preset stations quantity	40
Optical drive included	No
Product color	Silver
Audio decoders	Dolby Digital Plus, Dolby Pro Logic IIz, Dolby TrueHD, DTS-HD Master Audio
Apple docking compatibility	Not supported
AC input voltage	220-240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.2 W
Power consumption (typical)	720 W
THX-certified	THX Select2 Plus
Package weight	18500 g

Weight and Dimensions

Depth	398 mm
Width	435 mm
Height	198.5 mm
Weight	15000 g