Onkyo TX-SR502 Service Manual (English)

Other manuals for Onkyo TX-SR502

Service Manual118 pages

Instruction Manual60 pages

Questions and Answers:

J
Jennifer SmithAug 12, 2025
Why is there no sound coming from my Onkyo TX-SR502 Receiver speakers?
- R
  randyjacksonAug 12, 2025
  If no sound is coming from the speakers connected to your Onkyo Receiver, first, ensure the receiver isn't muted. If the MUTING indicator is on, unmute it. Check that all audio connecting plugs are fully inserted and the inputs/outputs of all components are correctly connected. Verify the speaker cables have correct polarity and bare wires are properly in the terminal. Select the correct input on your TV that corresponds to the AV Receiver connection. Also, disconnect any connected headphones. Set the input signal format to Auto, increase the volume, and configure the speaker settings, including specifying connected speakers, distances, and levels. Finally, ensure the source component is outputting digital audio in a compatible format.
A
Amanda PayneAug 16, 2025
How to fix an Onkyo Receiver when the subwoofer is not working?
- N
  Nicholas ColemanAug 16, 2025
  If the subwoofer connected to your Onkyo Receiver is not working or is very quiet, check the Speaker Configuration to ensure the Subwoofer setting is not set to No. Also, verify that the subwoofer volume is not set to the minimum. If speaker set A is turned off, turn it on, since the subwoofer output doesn't function when only speaker set B is active.
T
Tabitha DixonAug 19, 2025
What to do if tuner presets no longer work on Onkyo TX-SR502 Receiver?
- A
  Angela SmithAug 19, 2025
  If the tuner presets on your Onkyo Receiver no longer work, ensure the power cord is properly connected to a wall outlet. If the power has been off for an extended period, this can also cause the presets to be lost; reconnecting the power should resolve the issue.
U
umurphyAug 23, 2025
What to do if surround speakers are not working on Onkyo TX-SR502?
- E
  Eric PattersonAug 25, 2025
  If the surround speakers connected to your Onkyo Receiver are not working, first, check the listening mode, as some modes do not utilize surround speakers. If the listening mode is correct, try different source material, as some content may not heavily use surround speakers. Ensure that the surround speaker level is not set to minimum. Finally, verify that the Surround setting is properly configured in the Speaker Configuration.
C
Cynthia DeckerAug 27, 2025
How to troubleshoot no picture on TV with Onkyo TX-SR502 Receiver?
- Z
  Zachary LoveAug 28, 2025
  If there is no picture on the TV when using your Onkyo Receiver, change the listening mode, because the Pure Audio listening mode may be selected. Ensure the TV’s input selector is correctly set. Check that the video input and output formats are compatible.
O
owensthomasAug 31, 2025
Why is the center speaker not working on my Onkyo TX-SR502 Receiver?
- T
  Thomas VelezAug 31, 2025
  If the center speaker on your Onkyo Receiver is not working or is very quiet, the Stereo, Direct, Pure Audio, or Orchestra listening mode may be selected; try changing the listening mode. Check if the center speaker level is set to minimum and increase it if necessary. Also, ensure that the Center setting is correctly configured in the Speaker Configuration and is not set to None.
L
lisafosterSep 3, 2025
Why is only the center speaker working on my Onkyo TX-SR502 Receiver?
- J
  Jonathan TapiaSep 3, 2025
  If your Onkyo Receiver is only outputting sound from the center speaker, you may be listening to a mono sound source (like TV or AM broadcast) with the PL II/PL IIx Movie or PL II/PL IIx Music listening mode selected. Try changing the input source or the listening mode.
S
Stacey RamirezSep 7, 2025
What causes low frequency noise from Onkyo Receiver?
- G
  George JamesSep 8, 2025
  To address low-frequency noise or hum coming from your Onkyo Receiver, untangle the audio cables at the rear of the unit and position them as far away as possible from the power cord.

Onkyo TX-SR502 Specifications

General

Total Harmonic Distortion	0.08 %
Input Sensitivity	200 mV
Tuner Bands	AM/FM
Preset Stations	40
Power Output	75 Watts
Frequency Response	10Hz-100kHz
Amplifier Output Details	75W per channel (8 ohms, 20Hz-20kHz, 0.08% THD)
Response Bandwidth	10Hz-100kHz
Input Impedance	47 kOhm
Built-in Decoders	Dolby Digital, DTS
Surround Sound Effects	Dolby Pro Logic II
Width	435 mm
Depth	363 mm
Height	151 mm
Speaker Impedance	8 Ohm
Tuner Type	Digital
Remote Control	Yes
Dimensions (W x H x D)	435 x 151 x 363 mm