Why is my Orved Kitchen Appliances showing poor sealing?
If your Orved Kitchen Appliances machine isn't sealing properly, start by cleaning the sealing bar. If the issue continues, the sealing time might be insufficient for the bag's thickness. Try increasing the sealing time using the “SEAL” control knob. Also, inspect the Teflon cover and red silicone for wear and replace them if necessary.
What to do if Orved Kitchen Appliances does not create vacuum in chamber?
If your Orved Kitchen Appliances machine is not creating a vacuum in the chamber, ensure you lower the cover with both hands, applying sufficient pressure during appliance startup. Also, check that the jars evacuation valve (in models MULTIPLE-VM12-VM16) is closed. If you have a model with a gas option, make sure the gas function is deactivated using the “GAS” control knob. Finally, if none of the above work, the pump fuse (PF1) on the power board may have blown; in this case, contact a service center to change the fuse.
Why the Orved VM20 TANDEM machine does not seal?
If your Orved Kitchen Appliances machine is not sealing bags, first check the sealing bar connection wires and clean the contacts if necessary. If you have a model with a gas option, ensure the gas quantity is not more than 70% by adjusting the “GAS” control knob. Also, verify that the sealing bar fuse (PF2) on the power board is intact and replace it if blown. Finally, make sure the seal bag is not perforated, and replace it if necessary.
How to fix insufficient vacuum in chamber of Orved Kitchen Appliances?
If you're experiencing insufficient vacuum in the chamber of your Orved Kitchen Appliances, first, increase the evacuation time using the “VAC” control knob. Then, check the oil and the pump exhaust filter to ensure the vacuum pump performance is sufficient. If the cover gasket is worn, replace it. For models MULTIPLE - VM12 - VM16, ensure the external containers evacuation valve is closed.
How to prevent seal seam burns and bubbles in Orved Kitchen Appliances?
If the seal seam of your Orved Kitchen Appliances shows burns and bubbles, it means the sealing time is too long. Decrease the sealing time using the “SEAL” control knob.
What to do if Orved VM20 TANDEM Kitchen Appliances has insufficient vacuum in bag?
If you find that the vacuum in the bag is insufficient or the bag does not maintain vacuum with your Orved Kitchen Appliances, ensure the bag is positioned correctly, centered on the sealing bar and projecting 20 mm beyond it. If the bag is perforated, use a thicker bag and wrap the product with cling film or soft paper. If the sealing is insufficient, increase the sealing time using the “SEAL” control knob. Also, check the bag for defects and replace it if necessary. Ensure the bag opening is clean, free from oil or grease, and that the bag size is appropriate for the product dimensions.
How to troubleshoot Orved VM20 TANDEM machine not working?
If your Orved Kitchen Appliances machine isn't working, first, ensure it's switched on using the main power switch. Next, check the power supply by verifying the plug is correctly inserted into a functioning socket with the correct voltage and that the power cable is intact. Also, inspect fuses PF3 and PF4 on the power board to confirm they are intact and correctly inserted. If the problem persists, it may indicate machine damage, and you should contact a service center.
Why PLexiglas cover of Orved Kitchen Appliances does not close?
If the Plexiglas cover of your Orved Kitchen Appliances does not close, the cover gasket may be worn and needs replacement. Alternatively, the hinges might be out of alignment, requiring adjustment; contact a service center for hinge adjustments.
How to fix narrow irregular sealseam on Orved VM20 TANDEM?
If you observe a narrow, irregular seal seam on your Orved Kitchen Appliances, the sealing time is likely too short. Increase the sealing time using the “SEAL” control knob.
What to do if lid opens during GAS cycle of Orved VM20 TANDEM?
If the lid of your Orved Kitchen Appliances opens during the GAS cycle, the gas percentage is likely too high. Reduce the gas percentage using the “GAS” control knob.
Detailed technical specifications for various machine models.
Essential safety and operational regulations for using the vacuum packaging machine.
Explanation of the electro-mechanical and digital control panels and their functions.
Detailed explanations of core functions like VACUUM, GAS, SEAL, SOFTAIR, and JARS.
Comprehensive list of main spare parts with corresponding codes for various models.
Basic operational procedures for vacuum and sealing bags with electro-mechanical controls.
Guide to programming functions on digital control models.
Programming guide for digital control models of specific series.
Specific instructions and warnings for vacuum packaging liquid products.
Common problems and their solutions for both electro-mechanical and digital versions.
General| Category | Kitchen Appliances |
|---|---|
| Type | Vacuum Packaging Machine |
| Model | VM20 TANDEM |
| Pump capacity | 20 m³/h |
| Dimensions | 310x480x350 mm |
| Weight | 30 kg |
| Vacuum Level | 99.9% |
| Power | 1.2 kW |
| Voltage | 230V |
| Power supply | 230V/50Hz |
| Sealing System | Double sealing |
| Frequency | 50Hz |
To Next Page
