Why is my Orved VM12 showing poor sealing?
If your Orved Kitchen Appliances machine isn't sealing properly, start by cleaning the sealing bar. If the issue continues, the sealing time might be insufficient for the bag's thickness. Try increasing the sealing time using the “SEAL” control knob. Also, inspect the Teflon cover and red silicone for wear and replace them if necessary.
What to do if Orved Kitchen Appliances does not create vacuum in chamber?
If your Orved Kitchen Appliances machine is not creating a vacuum in the chamber, ensure you lower the cover with both hands, applying sufficient pressure during appliance startup. Also, check that the jars evacuation valve (in models MULTIPLE-VM12-VM16) is closed. If you have a model with a gas option, make sure the gas function is deactivated using the “GAS” control knob. Finally, if none of the above work, the pump fuse (PF1) on the power board may have blown; in this case, contact a service center to change the fuse.
Why the Orved Kitchen Appliances machine does not seal?
If your Orved Kitchen Appliances machine is not sealing bags, first check the sealing bar connection wires and clean the contacts if necessary. If you have a model with a gas option, ensure the gas quantity is not more than 70% by adjusting the “GAS” control knob. Also, verify that the sealing bar fuse (PF2) on the power board is intact and replace it if blown. Finally, make sure the seal bag is not perforated, and replace it if necessary.
How to fix insufficient vacuum in chamber of Orved Kitchen Appliances?
If you're experiencing insufficient vacuum in the chamber of your Orved Kitchen Appliances, first, increase the evacuation time using the “VAC” control knob. Then, check the oil and the pump exhaust filter to ensure the vacuum pump performance is sufficient. If the cover gasket is worn, replace it. For models MULTIPLE - VM12 - VM16, ensure the external containers evacuation valve is closed.
How to prevent seal seam burns and bubbles in Orved Kitchen Appliances?
If the seal seam of your Orved Kitchen Appliances shows burns and bubbles, it means the sealing time is too long. Decrease the sealing time using the “SEAL” control knob.
What to do if Orved Kitchen Appliances has insufficient vacuum in bag?
If you find that the vacuum in the bag is insufficient or the bag does not maintain vacuum with your Orved Kitchen Appliances, ensure the bag is positioned correctly, centered on the sealing bar and projecting 20 mm beyond it. If the bag is perforated, use a thicker bag and wrap the product with cling film or soft paper. If the sealing is insufficient, increase the sealing time using the “SEAL” control knob. Also, check the bag for defects and replace it if necessary. Ensure the bag opening is clean, free from oil or grease, and that the bag size is appropriate for the product dimensions.
How to troubleshoot Orved VM12 machine not working?
If your Orved Kitchen Appliances machine isn't working, first, ensure it's switched on using the main power switch. Next, check the power supply by verifying the plug is correctly inserted into a functioning socket with the correct voltage and that the power cable is intact. Also, inspect fuses PF3 and PF4 on the power board to confirm they are intact and correctly inserted. If the problem persists, it may indicate machine damage, and you should contact a service center.
Why PLexiglas cover of Orved VM12 does not close?
If the Plexiglas cover of your Orved Kitchen Appliances does not close, the cover gasket may be worn and needs replacement. Alternatively, the hinges might be out of alignment, requiring adjustment; contact a service center for hinge adjustments.
How to fix narrow irregular sealseam on Orved VM12 Kitchen Appliances?
If you observe a narrow, irregular seal seam on your Orved Kitchen Appliances, the sealing time is likely too short. Increase the sealing time using the “SEAL” control knob.
What to do if lid opens during GAS cycle of Orved VM12?
If the lid of your Orved Kitchen Appliances opens during the GAS cycle, the gas percentage is likely too high. Reduce the gas percentage using the “GAS” control knob.
Explanation of symbols and general hazards from machine use, operators, and safety devices.
Safety rules for electrical systems and maintenance operations.
Technical specifications for various models, dimensions, voltage, and power.
Continued specifications: pump oil, environmental conditions, and functions.
Electrical safety, earthing, plug handling, machine placement, and ventilation.
Explanation of the vacuum function for electromechanical and digital models.
Steps for preparing the machine, product, and calibrating the vacuum sensor.
Basic operation steps for electromechanical models.
Operation steps when using the gas option with electromechanical controls.
Calibrating vacuum sensor and programming functions for digital models.
Detailed steps for programming VAC, GAS, SEAL, SOFTAIR functions.
Programming VAC, GAS, SEAL, SOFTAIR functions for specific digital models.
Detailed steps for programming VAC+, GAS, SEAL, SOFTAIR functions.
Steps for packing liquid products, including using an inclined top.
Crucial warnings regarding product preparation, calibration, and altitude.
Safety warnings for maintenance and repair operations.
Scheduled maintenance tasks based on frequency for pump, cables, covers, and bars.
Safety precautions for cleaning, avoiding electric shock, burns, and proper detergent use.
Procedure for changing pump oil, including types of oil and models.
Machine not working, insufficient vacuum, no vacuum, cover not closing, bag vacuum issues.
Problems with sealing quality, bag perforation, defects, or size.
General| Brand | Orved |
|---|---|
| Model | VM12 |
| Category | Kitchen Appliances |
| Language | English |
To Next Page
