Why is my Orved VM18 showing poor sealing?
If your Orved Kitchen Appliances machine isn't sealing properly, start by cleaning the sealing bar. If the issue continues, the sealing time might be insufficient for the bag's thickness. Try increasing the sealing time using the “SEAL” control knob. Also, inspect the Teflon cover and red silicone for wear and replace them if necessary.
What to do if Orved VM18 does not create vacuum in chamber?
If your Orved Kitchen Appliances machine is not creating a vacuum in the chamber, ensure you lower the cover with both hands, applying sufficient pressure during appliance startup. Also, check that the jars evacuation valve (in models MULTIPLE-VM12-VM16) is closed. If you have a model with a gas option, make sure the gas function is deactivated using the “GAS” control knob. Finally, if none of the above work, the pump fuse (PF1) on the power board may have blown; in this case, contact a service center to change the fuse.
Why the Orved VM18 machine does not seal?
If your Orved Kitchen Appliances machine is not sealing bags, first check the sealing bar connection wires and clean the contacts if necessary. If you have a model with a gas option, ensure the gas quantity is not more than 70% by adjusting the “GAS” control knob. Also, verify that the sealing bar fuse (PF2) on the power board is intact and replace it if blown. Finally, make sure the seal bag is not perforated, and replace it if necessary.
How to fix insufficient vacuum in chamber of Orved VM18 Kitchen Appliances?
If you're experiencing insufficient vacuum in the chamber of your Orved Kitchen Appliances, first, increase the evacuation time using the “VAC” control knob. Then, check the oil and the pump exhaust filter to ensure the vacuum pump performance is sufficient. If the cover gasket is worn, replace it. For models MULTIPLE - VM12 - VM16, ensure the external containers evacuation valve is closed.
How to prevent seal seam burns and bubbles in Orved VM18 Kitchen Appliances?
If the seal seam of your Orved Kitchen Appliances shows burns and bubbles, it means the sealing time is too long. Decrease the sealing time using the “SEAL” control knob.
What to do if Orved VM18 Kitchen Appliances has insufficient vacuum in bag?
If you find that the vacuum in the bag is insufficient or the bag does not maintain vacuum with your Orved Kitchen Appliances, ensure the bag is positioned correctly, centered on the sealing bar and projecting 20 mm beyond it. If the bag is perforated, use a thicker bag and wrap the product with cling film or soft paper. If the sealing is insufficient, increase the sealing time using the “SEAL” control knob. Also, check the bag for defects and replace it if necessary. Ensure the bag opening is clean, free from oil or grease, and that the bag size is appropriate for the product dimensions.
How to troubleshoot Orved VM18 machine not working?
If your Orved Kitchen Appliances machine isn't working, first, ensure it's switched on using the main power switch. Next, check the power supply by verifying the plug is correctly inserted into a functioning socket with the correct voltage and that the power cable is intact. Also, inspect fuses PF3 and PF4 on the power board to confirm they are intact and correctly inserted. If the problem persists, it may indicate machine damage, and you should contact a service center.
Why PLexiglas cover of Orved Kitchen Appliances does not close?
If the Plexiglas cover of your Orved Kitchen Appliances does not close, the cover gasket may be worn and needs replacement. Alternatively, the hinges might be out of alignment, requiring adjustment; contact a service center for hinge adjustments.
How to fix narrow irregular sealseam on Orved VM18 Kitchen Appliances?
If you observe a narrow, irregular seal seam on your Orved Kitchen Appliances, the sealing time is likely too short. Increase the sealing time using the “SEAL” control knob.
What to do if lid opens during GAS cycle of Orved VM18?
If the lid of your Orved Kitchen Appliances opens during the GAS cycle, the gas percentage is likely too high. Reduce the gas percentage using the “GAS” control knob.
Explains various symbols used in the manual to highlight risks and important information for safe operation.
Covers dangers related to machine use, operators, safety devices, electrical hazards, modification, fire, cleaning, pneumatic springs, and gas options.
Essential safety rules and precautions for operating the vacuum packaging machine.
Overview of the control panel features for both electro-mechanical and digital versions of the machines.
Step-by-step guide for operating the vacuum packaging machines, covering different control types and options.
Comprehensive guide to operating and programming machines with digital control systems, including calibration and function settings.
Essential safety precautions to be followed before performing any maintenance or repair operations.
Identifies potential causes like machine being off or power supply issues and their solutions.
Addresses issues like insufficient time setting or pump performance and provides solutions.
Solutions for problems related to insufficient vacuum, such as gasket wear or valve issues.
Solutions for problems like bag perforation, incorrect sealing, or bag defects.
Troubleshooting steps for issues preventing the machine from sealing bags correctly.
General| Category | Kitchen Appliances |
|---|---|
| Vacuum Pressure | 2 mbar |
| External Vacuum | Yes |
| Sealing Bar Length | 450 mm |
| Voltage | 230 V |
| Material | Stainless Steel |
| Frequency | 50 Hz |
| Type | Vacuum Sealer |
To Next Page
