EasyManua.ls Logo

Ozito SCMS-10STAND - User Manual

Ozito SCMS-10STAND
10 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
ozito.com.au
SLIDING
COMPOUND
MITRE SAW
254mm (10”)
INSTRUCTION MANUAL
SPECIFICATIONS
Motor: 1900W
No Load Speed: 4,800/min
Blade: Ø254mm x Ø25.4 x 48T
Mitre Angle: 0-45° left & right
Bevel Angle: 0-45° left
Max. Cutting Capacity:
Mitre 0° x Bevel 90°: 70 x 310mm
Mitre 45°x Bevel 90°: 70 x 210mm
Mitre 0°x Bevel 45°: 40 x 310mm
Mitre 45°x Bevel 45°: 40 x 210mm
SCMS-10STAND
WHAT’S IN THE BOX
Material Clamp
Compound Mitre Saw
Material Support Bar x 2
Hex Key
Dust Bag
WARRANTY
0917
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from the
original date of purchase and is intended for DIY (Do It Yourself) use
only. If a product is defective it will be replaced in accordance with
the terms of this warranty. Warranty excludes consumable parts, for
example: blade, carbon brushes and dust bag.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction
manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO
Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.

Table of Contents

Questions and Answers

  • D
    drosalesAug 16, 2025
    What to do if Ozito Mitre Saw will not start?
    • J
      Jill JamesAug 16, 2025
      If your Ozito Mitre Saw isn't starting, the issue might be with the power supply. Check to ensure that the power cord is properly connected to a working power outlet and that the power switch is turned on.
  • J
    Julie CherryAug 18, 2025
    What to do if Ozito SCMS-10STAND Saw is not cutting straight?
    • J
      Jennifer GilbertAug 19, 2025
      If your Ozito saw is not cutting straight, it could be due to the rear fence being out of alignment. Follow the instructions in this manual to realign the rear fence.
  • D
    Dale VasquezAug 22, 2025
    Why does my Ozito Mitre Saw operate sporadically?
    • A
      Andrea OrozcoAug 22, 2025
      If your Ozito Mitre Saw is operating sporadically or at low power, it could be due to a low power supply or an improper extension cord. Inspect the power supply and cords. Another potential cause is worn or cracked carbon brushes, so inspect them and replace if damaged or worn.
  • T
    Timothy BrownAug 25, 2025
    What to do if the laser does not turn on on my Ozito SCMS-10STAND Saw?
    • K
      Kathy HannaAug 26, 2025
      If the laser on your Ozito saw isn't turning on, make sure the required batteries are correctly installed and that the laser switch is in the 'on' position.
  • C
    carolynowensAug 28, 2025
    What to do if wood burns at ends of cut with Ozito SCMS-10STAND?
    • J
      Jessica DoughertyAug 28, 2025
      If the wood burns at the ends of the cut when using your Ozito saw, it could be due to a dirty or worn blade. Clean the blade with blade cleaner or mineral spirits, or replace it if it's worn or damaged. Another cause may be that the material is binding. Ensure the workpiece is flat, flush against the fence, and supported on the ends.
  • B
    Brandon ChenAug 30, 2025
    What causes workpiece to fray or chip out when using Ozito Saw?
    • J
      jonathanlongAug 30, 2025
      If the workpiece frays or chips out when using your Ozito saw, ensure the finish side is up or facing the operator. Check the blade for damage or dullness and sharpen or replace it if needed. Also, verify that the blade is appropriate for the material you're cutting. For cross-cutting hardwood or precision cuts, use a thin kerf blade with 60 or more teeth. Finally, make sure the workpiece is supported; use a thin piece of scrap material to support the edges during cutting.
  • L
    Lisa HernandezSep 3, 2025
    What to do if blade binds when using Ozito Saw?
    • J
      James BoltonSep 3, 2025
      If the blade binds, slowing or stopping your Ozito saw, it could be because the workpiece is misaligned or not supported. Ensure the workpiece is flat on the table, flush against the fence, and supported at both ends. Also, the workpiece might be wet or contaminated, or the blade is inappropriate for the workpiece. Check the condition of the workpiece and the compatibility of the blade.
  • B
    Bryan JeffersonSep 6, 2025
    What to do if Ozito SCMS-10STAND blade does not cut completely through workpiece?
    • M
      Mark HayesSep 6, 2025
      If the blade of your Ozito saw does not cut completely through the workpiece, check if the depth stop setting is in use and push it in to disengage. If the depth stop is set too shallow, adjust the depth stop bolt for the desired depth of cut.
  • A
    Andrew FloresSep 9, 2025
    Why 45° bevel is not accurate on Ozito Saw?
    • D
      Desiree SimsSep 9, 2025
      If the 45° bevel on your Ozito saw is not accurate, the bump stop may be misaligned. Follow the instructions in this manual to realign the rear fence.
  • B
    Brittany MurphySep 12, 2025
    How to align laser on Ozito SCMS-10STAND?
    • M
      Maria NashSep 12, 2025
      If the laser on your Ozito saw is not aligned with the blade cut line, it's possible that the laser unit is misaligned. Adjust the laser alignment following the instructions in this manual.

Summary

Specifications

Whats In The Box

Warranty

3 Year Replacement Warranty

Details the terms and conditions of the 3-year replacement warranty.

Know Your Product

Setup & Preparation

Assembly

Instructions for assembling the mitre saw and its components.

Set-Up and Adjustments

Bench Mounting

Details how to securely mount the mitre saw to a workbench or stand.

Slide Lock

Explains how to engage the slide lock for cutting narrow pieces of wood.

Mitre Angle Adjustment

Instructions on how to adjust the mitre angle of the saw blade.

Bevel Angle Adjustment

Guides on how to set and adjust the bevel angle of the cutting head.

Trenching

Explains how to set up the saw for trenching or cutting grooves.

Operation

Types of Cuts

Describes different types of cuts that can be performed with the mitre saw.

Spindle Lock

Explains the function and use of the spindle lock for blade changes.

Retractable Safety Guard

Details the operation and importance of the retractable safety guard.

Fence

Instructions on ensuring the fence is correctly positioned for safe cutting.

Material Clamp

Guidance on using the material clamp to secure the workpiece.

Operating the Saw

Turning On and Off

Instructions on how to start and stop the mitre saw.

Laser Guide

Details on operating the laser guide for precise cutting.

Workpiece

Guidance on correctly placing and securing the workpiece on the table.

Slide Action

Instructions on how to use the slide action for wider cuts.

Saw Alignment

Fence Alignment

Steps to ensure the fence is perpendicular to the saw blade for accurate cuts.

Bevel Alignment

Procedure to adjust the saw's bump stops for accurate bevel angles.

Laser Alignment

How to adjust the laser guide to align with the blade cutting line.

Maintenance

Changing the Blade

Detailed instructions for safely replacing the saw blade.

Troubleshooting

Spare Parts

Caring for the Environment

Electrical Safety

General Power Tool Safety Warnings - Personal Safety

Mitre Saw Safety Warnings

Stand Assembly

Ozito SCMS-10STAND Specifications

General IconGeneral
BrandOzito
ModelSCMS-10STAND
CategorySaw
LanguageEnglish

Related product manuals