14
The unit can access the picture monitor on a CCU to control the ROP
menu (REMOTE OPERATION MENU).
CHARA
MENU
SELECT
REMOTEOPERATIONMENU
SHADING(WHITE)
PEDESTAL/FLARE/GAIN
GAMMA/BLACKGAMMA
CINEMAGAMMA
KNEE/WHITECLIP
MATRIX
HDDTL/SKINDTL
SDDETAIL
SYSTEM
FUNCTION
LENSFILE/EDIT
Hold down <CHARA/MENU> for about 2 seconds to
open [REMOTE OPERATION MENU]. To close
[REMOTE OPERATION MENU], hold down
<CHARA/MENU> for about 2 seconds.
Use <SELECT> to select the menu.
Menus cannot be displayed when any of the following messages appear
on the picture monitor.
• WARNING message
• AUTO message
• STATUS message
If any of these messages appear, you can hold down <CHARA/MENU>
to delete them and resume operation.
When camera power <HEAD POWER> is Off, only [SYSTEM] can be
selected.
The [REMOTE OPERATION MENU] appears. (The cursor appears at
the beginning of the first line.)
CHARA
MENU
SELECT
→
＊ ＲＥＭＯＴＥ ＯＰＥＲＡＴＩＯＮ ＭＥＮＵ ＊
ＳＨＡＤＩＮＧ（ＷＨＩＴＥ ）
ＰＥＤＥＳＴＡＬ／ＦＬＡＲＥ／ＧＡＩＮ
ＧＡＭＭＡ／ＢＬＡＣＫ ＧＡＭＭＡ
ＣＩＮＥＭＡ ＧＡＭＭＡ
ＫＮＥＥ／ＷＨＩＴＥ ＣＬＩＰ
ＭＡＴＲＩＸ
ＨＤ ＤＴＬ／ＳＫＩＮ ＤＴＬ
ＳＤ ＤＥＴＡＩＬ
ＳＹＳＴＥＭ
ＦＵＮＣＴＩＯＮ
ＬＥＮＳ ＦＩＬＥ／ＥＤＩＴ
Cursor
CHARA
MENU
SELECT
→
＊ ＲＥＭＯＴＥ ＯＰＥＲＡＴＩＯＮ ＭＥＮＵ ＊
ＳＨＡＤＩＮＧ（ＷＨＩＴＥ ）
ＰＥＤＥＳＴＡＬ／ＦＬＡＲＥ／ＧＡＩＮ
ＧＡＭＭＡ／ＢＬＡＣＫ ＧＡＭＭＡ
ＣＩＮＥＭＡ ＧＡＭＭＡ
ＫＮＥＥ／ＷＨＩＴＥ ＣＬＩＰ
ＭＡＴＲＩＸ
ＨＤ ＤＴＬ／ＳＫＩＮ ＤＴＬ
ＳＤ ＤＥＴＡＩＬ
ＳＹＳＴＥＭ
ＦＵＮＣＴＩＯＮ
ＬＥＮＳ ＦＩＬＥ／ＥＤＩＴ
Cursor
The [SHADING(WHITE)] menu appears.
In this state (when the cursor is in the menu title), press <SELECT> to
return to the next higher menu ([ROP MENU]).
CHARA
MENU
SELECT
＊＊ ＳＨＡＤＩＮＧ（ ＷＨＩＴＥ ） ＊＊
ＷＨＩＴＥ ＳＨＡＤＩＮＧ ＳＷＩＴＣＨ
→
Ｇ
Ｂ
Ｒ
ＨＳＡＷ ＨＰＲＡ ＶＳＡＷ ＶＰＡＲＡ
ＯＮ
０ ０ ０ ０
０ ０ ０ ０
０ ０ ０ ０
The selected setting flashes allowing you to change the set value.
＊＊ ＳＨＡＤＩＮＧ（ ＷＨＩＴＥ ） ＊＊
ＷＨＩＴＥ ＳＨＡＤＩＮＧ ＳＷＩＴＣＨ
→
Ｇ
Ｂ
Ｒ
ＨＳＡＷ ＨＰＲＡ ＶＳＡＷ ＶＰＡＲＡ
ＯＮ
０ ０ ０ ０
０ ０ ０ ０
０ ０ ０ ０
Flashing
CHARA
MENU
SELECT
Turn <SELECT> quickly to change the hundreds place of a set value.
To Next Page
Loading...
