Panasonic CF-R1 Series

List
of
Error
Codes
The
following
is a
list
of
the
messages
that BIOS
can display.
Most
of them
occur during
POST. Some
of
them
display
informa-
tion
about
a
hanJware
device,
e.g., the
amount of
memory
installed.
Others may
indicate a problem with a
device,
such as the way
it has
been
configured.
Following
the
list are
explanations
of
the
messages
and remedies
for reported
problems.
If
your
system
displays
any
of
the
below
error
messages
other that
the
ones
marked with an
asterisk
(*),
write down
the
message
and
contact
Panasonic
Technical
Support.
If
your system
fails
after
you make changes
in
the
Setup menus,
reset
the
computer,
enter
Setup
and
install
Setup
defaults
or
correct
the error.
0200
Failure
Fixed
Disk
Fixed
disk in
not
working
or not
configured
properly.
Check
to see if
fixed disk
is attached
properly. Run Setup. Find
out if the
fixed-di.sk
type
is
correctly
identified.
0210
Stuck key
Stuck
key
on
keyboard.
0211
Keyboard
error
Keyboard
not
working.
0212
Keyboard
Controller
Failed
Keyboard
controller
failed
test. May
require
replacing
keyboard
controller.
0213
Keyboard
locked
-
Unlock key
switch
Unlock
the
system
to
proceed.
0230
System
RAM
Failed
at offset
:
nnnn
System
RAM
failed at
offset
nnnn
of
the 64k
block at
which the
error
was
detected.
0231
Shadow
RAM
Failed
at
offset
;
nnnn
Shadow
RAM
failed at
offset
nnnn
of the 64k
block at
which the
error
was
detected,
0232
Extended
RAM
Failed
at
offset
:
nnnn
Extended
memory
not
working
or
not
configured
properly
at offset
mnn.
0250
System
battery
is
dead
-
Replace
and
run
SETUP
The
CMOS
clock battery
indicator
shows
the
battery is
dead.
Replace
the
battery and
run
Setup to reconfigure
the system.
*0251
System
CMOS
ciiecksum
bad
•
Default
configuration
used
System
CMOS
has been
corrupted
or modified
incorrectly,
perhaps by an
application program that
changes
data
stored
in
CMOS.
The
BIOS
installed
Default
SETUP
Values.
If you
do
not want
these
values,
enter
Setup
and enter your
own
values. If
the
error
persists, check
the
system
battery
or
contact
Panasonic Technical
Support.
,
0260
System
timer
error
The
timer test
failed.
Requires
repair
of
system
board.
0270
Real time
clock
error
Real-time
clock
fails
BIOS test. May
require board
repair.
0280
Previous
boot
incomplete
-
Default configuration
used
Previous
POST
did not
complete
successfully.
POST
loads
default
values
and
offers
to run
Setup. If
the failure
was caused
by
incorrect
values and
they
are not
corrected,
the
next boot
will
likely
fail,
On
systems with control of
wait states,
improper
Setup settings can
also
terminate
POST
and
cau.se
this
error
on the
next
boot.
Run Setup
and verify that the wait-state
configuration
is
correct.
This error
is
cleared the
next
time the
system is
booted.
0281
Memory
Size
found
by POST
differed
from EISA
CMOS
Memory
size
found
by
POST
differed
from EISA CMOS.
02B0
Diskette
drive A
error
02B1
Diskette
drive B
error
Drive
A: or B:
is
present
but fails the BIOS
POST
diskette
tests.
Check to
see
that
the
drive
is defined with the
proper
diskette type in
Setup
and
that
the
diskette
drive
is attached
correctly.
02B2
Incorrect
Drive A
type
-
run
SETUP
Type
of floppy
drive
A:
not correctly identified
in Setup.
02B3
Incorrect
Drive B
type
-
run SETUP
Type
of floppy
drive B:
not correctly
identified
in Setup.
02D0
System
cache
error
-
Cache disabled
Contact
Panasonic
Technical
Support.
02F0;
CPU
ID:
CPU
socket
number
for
Multi-Processor
error.
02F4:
EISA
CMOS
not
writable
ServerB10S2
test error:
Cannot
write
to EISA
CMOS.
19