Timer Recording
Tips
RAM
-RW(V)
+R
+RW
To use a new disc, formatting is necessary.
To check programmes (➔ 35)
To cancel a timer recording
programming
1. Press [
e
,
r
,
w
,
q
] to select the
programme (the timer icon is displayed)
and press [OK].
2. While “Delete” is selected, press [OK].
3. Press [
w
,
q
] to select “Yes” and press
[OK].
– The timer icon disappears.
Notes
The GUIDE Plus+ list is not displayed
immediately after initial tuning is done.
The GUIDE Plus+ system will not work
if the clock is not set correctly.
If “NTSC” has been selected for “TV
System” (➔ 82), the GUIDE Plus+
system cannot be used.
“FR” recording mode is not available
when the timer programme is controlled
by “Guide Link”.
If you set a timer recording that will
overlap with other timer recordings, the
“Overlapped Timer Recording” screen
appears to help you resolve the
overlapping.
Follow the on-screen instructions.
•
•
•
•
•
•
What is Freeview Playback?
Freeview Playback is the functions that enable timer recordings be controlled by the signal sent
from the broadcaster. “Guide Link”, “Series recording” (➔ 34), and “Split Programme” are available.
“Guide Link” — If you set a timer recording from the TV Guide, the recording’s start and
stop times can be controlled by the broadcaster, e.g. delayed start.
This is indicated by “Guide Link” in the Timer Recording screen in step 2 (➔ below).
“Split Programme” — If a programme is separated into 2 or more parts by some other
programmes e.g. news, this unit pauses recording during the gap.
This is indicated by “Split” in the Timer Recording screen in step 2 (➔ below).
When setting timer from the 1st split programme, other parts of the programme will be automatically
set and indicated by the timer icon on the TV Guide, but not shown on the timer recording list.
If you set a timer recording from the TV Guide, the recording’s start and stop times are
controlled by the signal sent from the broadcaster. If the signal is not sent correctly,
the recording may lack the beginning or the ending part of the programmes.
In order to make the timer recording work successfully, we recommend you set the
start time earlier and the end time later by some minutes, up to a maximum of 10
minutes for Guide Link to function.
e.g. When you set the timer recording for a programme that will start at 10:00 and end
at 11:00, set “9:58” and “11:05” in step 3 (➔ below).
HDD
RAM
-R
-RW(V)
+R
+RW
VHS
Preparation:
Turn on the television and select the appropriate video input to suit the
connections to this unit.
Turn on this unit.
If recording to DVD or VHS, insert a disc or video cassette that you use
for recording (➔ 89).
RAM
If the disc is protected, release protection (➔ 76).
VHS
Ensure accidental erasure tab is intact.
Confirm that the clock on the unit’s display is set to the correct time.
•
•
•
•
•
•
The GUIDE Plus+ list appears.–
e
,
r
,
w
,
q
to select the future programme, then
If “Selection Screen” appears, press [
e
,
r
] to select “Single Timer Rec.”, then press [OK].
Refer to “Series recording” (➔ 34) for “Series Timer Rec.”.
–
“Guide Link” and “Split” are displayed here.
Confirm the programme (start and end time) by
TV magazine, etc. and correct if necessary using
e
,
r
,
w
,
q
, then
The settings are stored and the timer programme is on.
The timer icon is displayed.
“
z
” lights on the unit’s display to indicate timer recording standby has been activated.
Repeat steps
2
-
3
to programme other recordings.
Press [
^
DVD/VHS] to turn the unit off.
–
–
–
–
–
To Next Page
Loading...
Need help?
General
