General Issues Operation
Page
Cannot operate the TV with the
unit’s remote control.
Change the manufacturer code on the remote control.
It may be necessary to set the code on the remote control again after
changing the batteries.
•
•
85
94
Cannot operate the DVD. Press [DRIVE SELECT] to select the DVD drive when operating DVDs or CDs.• 20
Cannot operate the VHS.
Press [DRIVE SELECT] to select the VHS drive when operating video cassettes.
• 20
The remote control doesn’t work. The remote control code is wrong. Change to the correct code.
The batteries are depleted. Replace them with new ones.
Point the remote control at the remote control sensor on the main unit.
Remove obstacles between the remote control and the main unit.
Remove dust from the transmission window and the unit’s sensor.
Coloured glass may obstruct the signal reception/transmission.
Don’t place the signal sensor in direct sunlight or in areas that may be subject
to sun exposure.
It may be necessary to set the manufacturer code again after changing the batteries.
The Child Lock function is activated.
•
•
•
•
•
•
•
•
•
94
7
7
−
−
−
−
85
85
The unit is on but cannot be
operated.
Recording drive or playback drive has not been selected properly.
Some operations are prohibited by the disc.
The unit is warm (“U59” appears on the unit’s display). Wait until “U59” disappears.
One of the unit’s safety devices may have been activated.
Reset the unit as follows:
Press [
8
] on the main unit to switch to standby mode.
If the unit doesn’t switch to standby mode, reset the unit (➔ 94, “To restore the
unit if it freezes”).
The unit cannot be operated while performing an update. “SW-DL” appears on
the unit’s display while it is updating. Please wait until the “SW-DL” disappears.
•
•
•
•
•
20, 21
−
92
−
84
“U88” is displayed and the disc
cannot be ejected.
The unit is carrying out the recovery process.
The disc may be defective.
Do
the following to eject the disc.
Try another disc.
(1) Press [
8
] on the main unit to switch to standby mode.
If the unit doesn’t switch to standby mode, reset the unit (➔ 94, “To restore
the unit if it freezes”).
(2)
While the unit is turned off, press and hold [
g
] and [CH
1
] on the main
unit at the same time for about 5 seconds. (Ejection may take extra time
depending on discs.)
• −
Cannot eject a disc. The unit is recording.
The unit may have a problem. Eject the disc as in (2) above.
Linked timer recordings with external equipment is in recording standby
(“EXT-L” on the unit’s display blinks when [
^
DVD/VHS] is pressed). Press
[EXT LINK] to cancel the recording standby.
If the Child Lock function is activated, above operation does not work. Cancel
the Child Lock function.
•
•
•
−
−
31, 85
Startup is slow. Startup takes time in the following situations:
A disc other than a DVD-RAM is inserted.
The clock is not set.
Immediately after a power failure or the AC mains lead is connected.
When the unit is connected with an HDMI cable.
When “Power Save” is set to “Off”, startup becomes faster than when “Power
Save” is “On”
.
•
–
–
–
–
•
−
84
General Issues GUIDE Plus+
Page
The GUIDE Plus+ system does
not receive any data.
Check whether the clock is properly set.
If signal quality is bad (ghost images or limited reception), the GUIDE Plus+
system may not be able to receive any data.
Perform “Auto-Setup Restart” in the Setup menu.
•
•
•
14
−
79
“No Data” is displayed for some or
all stations.
Some stations are not supported by the GUIDE Plus+ system.
Programme the Timer recording manually.
Perform “Auto-Setup Restart” in the Setup menu.
•
•
•
−
34
79
The GUIDE Plus+ information is
not displayed properly.
There was a programme change or GUIDE Plus+ information from a
broadcast station was possibly not correctly transmitted.
Check the current programme, e.g. on the Web site for the GUIDE Plus+
system provider or station provider.
• −
The GUIDE Plus+ data is not
updated.
The unit must be in standby mode in order to update the data. If the unit is in EXT LINK
mode (“EXT-L” lights up in the unit’s display), then the data update may also not work.
Make sure that the time is set correctly.
Check whether “Off” is set under “TV Guide Download in Standby” and change
the setting in System Update in the Setup menu.
•
•
•
−
14
84
Troubleshooting Guide
To Next Page
Loading...
Need help?
General
