TV
screen and video
Page
The
images
trom
this
unit
• Make sure that the television
is
connected to either the VIDEO OUT terminal,
11
do
not
appear
on
the
COMPONENT VIDEO OUT terminals or HDMI
AV
OUT terminal on this unit.
television.
• Make sure that the television's input setting (e.g., VIDEO 1)
is
correct.
-
• An incorrect resolution is selected
in
"Component Video Resolution", when the
32
Picture
is
distorted.
television is connected to COMPONENT VIDEO OUT terminals. While stopped,
press and hold
[.]
and
(~]
(PLAY) on the main unit at the same time for more
Jittering
occurs.
than 5 seconds to cancel this setting. Set the item again.
• If "24p Output" is set to "On" when the unit is connected to a TV through any
32
terminal other than HDMI, images may not display properly.
In
this case, set "24p
Outpuf' to "Off'.
• When "24p
Outpuf
is set to "On", HDMI authentication takes place where 24p 32
images switch to other images, and a black screen is displayed.
• When "24p
Outpuf
is set to "On". jittering may occur while playing DVD-Video 32
other than 24p images. In this case, turn "24p Output" to "Off'.
•
1!m3:
Images may not be output due to how files were created.
-
• Press
[.]
and
[~]
(PLAY) simultaneously on the unit for more than 5 seconds to
33
shift
to
more compatible mode with HDMI equipment. However, Dolby Digital
Plus, Dolby TrueHD, and DTS-HD audio are not output
in
bitstream.
To
output the
bitstream, select "Restore Default Settings" to restore the factory presets and
make proper settings.
• Picture may not be seen when more than 4 devices are connected with HDMI
--
cables. Reduce the number of connected devices.
The
screen
changes
• When the "Screen Saver Function" in the Setup menu
is
set to "On", the display
32
automatically. may return to the screen saver mode automatically if there is
no
operation for
10 minutes or more.
Video
is
not
output
in
high
• High definition video cannot be output through the VIDEO OUT terminals. -
definition.
• Confirm that the "HDMI Video Mode", "HDMI Resolution", and "Component Video 32
Resolution" in the Setup menu are set properly.
The
4:3
aspect
ratio
picture
• Use the television to change the aspect. Refer to your television's operating -
expands
left
and
right.
instructions.
• When using a component video cable, set "Progressive" to "Video".
If
the situation
29,32
Screen size
is
wrong.
is
not restored after that, set "TV Aspecf' to "4:3 Pan & Scan".
• When using an HDMI cable, change "TV Aspect" type to "16:9".
32
There
Is
a
lot
ot
after-image
• Turn "3D NR" or "Integrated NR" off if it is on.
29
when
playing
video.
When
playing
DVD-Video
• When you use the HDMI
AV
OUT terminal for video output, follow the steps below 32
using
progressive
output,
for setting.
one
part
of
the
picture
1 Connect this unit to the
TV
with any cable except the HDMI cable.
momentarily
appears
to
be 2 When you connect with the Component Video cable, set "HDMI Video Mode" to
doubled
up.
"Off" and "Component Video Resolution" to "480i"
in
the Setup menu.
Still
pictures
(JPEG)
do
not
• The images that were edited
on
the
PC,
such as Progressive JPEG, etc., may not 35
playback
normally.
playback.
Sound
No
sound.
• Check the connections and the "Digital Audio Outpuf' settings. Check the input
11-13,31
Low
volume.
mode on the amplifier/receiver if you have connected one.
Distorted
sound.
• Press [AUDIOI to select the audio.
20
Cannot
hear
the
desired
• I
Bossi:
When the unit is connected to an amplifier/receiver with the AUDIO OUT
32,34
audio
type.
terminal, set "Analog Audio Output" and match multi channel speaker settings. If
these are not set properly, the audio
is
not output correctly.
• 1
BOSS
I:
When connected
to
an amplifier/receiver or any other devices using both 32
AUDIO OUT terminal and HDMI
AV
OUT terminal, the audio from AUDIO OUT
terminal may not be output with the desired audio depending on the specifications
of the connected deVices, etc. Set "HDMI Audio Output" to "Off", when you output
multi-channel surround sound from AUDIO OUT terminal.
• The sound effects (Re-master,
V.
Surround, etc.) will not work when the bitstream
-
signal is output from the HDMI
AV
OUT terminal or the DIGITAL AUDIO OUT
terminal.
•
1m!D:
Audio may not be output depending
on
how files were created.
-
• Audio may not be heard when more than 4 devices are connected with HDMI
-
cables. Reduce the number of connected devices.
•
To
output audio from a device connected with
an
HDMI cable, set "HDMI Audio 32
Output" to "On" in the Setup menu.
Cannot
switch
audio.
• There are discs for which audio cannot be changed because of how the disc was
-
created.
• When connecting an amplifier/receiver using a coaxial cable
('B055,),
optical
12,13,31
digital audio cable or an HDMI cable, you cannot switch the audio if "Dolby D/
Dolby D +/Dolby TrueHD" or "DTS/DTS-HD"
is
set to "Bitstream". Set "Dolby D/
Dolby D +/Dolby TrueHD" or "DTS/DTS-HD"
to
"PCM" or connect using AUDIO
OUT terminal.
.---------
I
I
/'
''\
1
-,._-----_._------_._--_._--_._---_._-
..
__
_---------.---_
..
-
----
_---_
_------
~
RQT9243
To Next Page
Loading...
