Audio and video information
About audio from audio output terminals
- .
Sefore connecting, read the table below, and confirm the desired audio type and necessary sel1ings ("SO-Video Secondary Audio", "Dolby D/Dolby
o +/Dolby TrueHD"
or
"DTS/DTS-HD").
(~
9)
• The number of channels listed
is
the maximum possible number
of
output channels.
HDMI
AV
OUT/DIGITAL AUDIO OUT (Coaxial
B055
Optical)
5.1ch PCM
7.1ch
PCM"'
1i1'!liI!J:
5.1
ch PCM
Down-mixed
2ch PCM
DTS Digital
Surround/
DTS-ES'6
DTS Digital
Surround
Down-niixed
2ch PCM
Dolby Digital7.1ch PCM
7.1ch PCM
1mI1:
7.1ch PCM"
5.1ch PCM'2
Down-mixed
5.1ch PCM'2
DTS Digital
Surround/
DTS-ES
7.1ch PCM
Dolby Digital
Plus
DTS-HD High
Resolution
Audio
Dolby TrueHD
DTS-HD Master
Audio
DTS Digital
Surround/
DTS-ES'6
DTS Digital
Surround
Down-mixed
5.1ch PCM
AUDIO
OUT
(Analog)
7.1ch"
Down-mixed
5.1ch*2
7.1ch
7.1ch
5.1ch 2ch
• Also, depending
on
the specifications
or
the settings of the amplifier/receiver, the results of the output may vary.
"1
When the connected equipment is not supported with these audio formats, the audio
is
output as Dolby Digital bitstream, DTS Digital Surround
bitstream
or
down-mixed 2ch PCM (e.g., TV).
"2
1mI1:
When playing SO-Video without secondary audio
or
clicking sound, the audio is output as the same format as if "SO-Video Secondary
Audio" was set to "Off".
'3
When the connected equipment is not supported with multi channel surround, the audio is output as down-mixed 2ch PCM.
'4
1mI1:
When the connected equipment is supported with
7.1
channel surround, the audio output
is
amplified from
5.1
ch
or
6.1
ch to
7,1
ch
depending on the DTS, Inc. specifications.
"5 With PCM output, Dolby Digital
EX
becomes PCM audio decoded as Dolby Digital, DTS-ES recorded
to
DVD-Video becomes PCM audio
decoded as DTS Digital Surround, and DTS-ES recorded to SO-Video becomes PCM audio decoded
as
DTS-ES.
'6
miI!i:
When "SO-Video Secondary Audio"
is
set to "On", Dolby Digital EX is output as Dolby Digital and DTS-ES is output as DTS Digital
Surround, however if playing SO-Video without secondary audio
or
clicking sound, the audio is output as the original format.
Enjoying High Bit rate Audio of BD-Video
miI!i
- .
This unit supports high bit rate audio (Dolby Digital Plus, Dolby TrueHD, DTS-HD High Resolution Audio and DTS-HD Master Audio) adopted
in
BD-Video.
In
order to enjoy these audio formats, the following conditions are necessary. (Part shown in the shaded area of table given above)
NECESSARY CONNECTIONS
• HDMI
AV
OUT
terminal: Connect this unit
to
your amplifier/receiver supporting HDMI (High Bit rate Audio) using a High Speed HDMI cable
(~
11).
•
7.1
ch AUDIO OUT terminal
~:
Connect this unit to your amplifier/receiver supporting
7.1
channels using audio cables
(~
12).
NECESSARY
SETIINGS
(~
9)
.Set
"SO-Video Secondary Audio" to "Off'.
• HDMI
AV
OUT
terminal: Set "Dolby D/Dolby 0 +/Dolby TrueHD"
or
"DTS/DTS-HD"
to
"Sitstream" or "PCM" .
• 7.1ch AUDIO OUT terminal
"J...Qss:':
Set "Analog Audio Output" to "7.1ch".
;'
(8
• The clicking sound on the menu and audio with secondary video
in
picture-in-picture mode
(~
21) is not output.
1\
~
..
_
...
-
.....
_......
---
..
-
..
ROT9243
To Next Page
Loading...
