Network settings
These settings are used if you will connect this unit
to
the Internet.
e
The
connection
to
the
Internet
may
take
time
or
the
Internet
may
not
be
connected
depending
on
the
connection
environment.
(~
35)
It
is
required that you use a broadband connection.
Preparation
eConnect
to
a broadband network.
(~
16)
Testing
of
"IP Address/DNS Settings"
Always test the connection when a
LAN
cable
is
connected.
o Press [SETUP].
e Press
[.A
I
T]
to
select
"Network"
and press [OK].
e Press
[.A,
T]
to
select "IP
Addressl
DNS
Settings"
and press [OK].
o Press
[.A
I
T]
to
select "Connection
Test" and press [OK].
Setting the
IP
address
In
most
cases,
default
settings
can
normally
be
used
without
making
any changes.
Set the IP
address
only
when the
router
has
no
DHCP
server
functions
or
when
the
router's
DHCP
server
function
is
disabled.
After performing steps
0-0
(¢
left)
o Press
[.A,
T]
to
select "IP
Address
Auto
Configuration (DHCP)" and
press [
.....
I
~]
to
select
"Off".
o Press
[.A
I
T]
to
select "IP
Address"
I
"Subnet
Mask"
or
"Default
Gateway" and press [OK].
o Enter numbers with the numbered
buttons
and press [OK].
o Press [
.....
,
~]
to
select
"Yes"
and
press [OK].
Setting the DNS·IP
eAfter checking the specifications for your broadband router, enter
each number. If the number
is
unknown, then check the number of
other devices such
as
personal computers connected via a
LAN
cable. Assign a different number from those of other devices for the
"IP Address" and the same number for others.
elf
a wrong number is entered, then press [CANCEL].
eThe numeric input range
is
between 0 and 255.
In
most
cases,
default
settings
can
normally
be
used
without
making
any
changes.
When
setting
an
assigned
DNS
server
from
your
Internet
service
provider,
perform
the
following
settings.
After performing steps
0-0
(¢
left)
,I
Delaun Gateway
)1
DNS
Auto
Configuration (DHCP)
I
I
PrimaryDNS
II
1
secondary
DNS
II
Auto Delect Connection Speed
I I
Connection Speed
setting
I I
gOK
O·
,0
RETURN
---~-~---
r
(~:=:~::,-~~~-;~'
==='--:1
':
!IP Address Auto Configuration (OHCP) I I I 1
[
IP
Address
II
1I
II
Subnet
Mask
=:J
I II
l
I
j
J
ePerform the "Connection Test" also when any change was made
to
the
"IP
Address/DNS Settings".
"Testing":
"Pass":
"Fail":
The test is in progress.
The connection is completed.
Press [RETURN] to exit.
Please
check
the
connection
and
settings.
(~
40)
o Press
[.A,
T]
to
select "DNS
Auto
Configuration (DHCP)" and press
[
.....
I
~]
to
select
"Off".
o Press
[.A,
T]
to
select
"Primary
DNS"
or
"Secondary DNS"and
press [OK].
o Enter numbers with the numbered
buttons
and press [OK).
elf
the connection test fails, it may
be
necessary
to
set the MAC
address of this unit at the router side. The MAC address can
be
displayed by pressing [SETUP] and selecting "Network".
BffJDD
o • 9
o Press [
.....
,
~]
to
select
"Yes"
and
press [OK].
eFollow the instructions given
by
your Internet service provider and
enter the numbers. If the number
is
unknown, then check the
number of other devices such as personal computers connected
via
a LAN cable and assign the same number.
elf
a wrong number
is
entered, then press [CANCEL].
eThe numeric input range
is
between 0 and 255.
.
...
:
17'
RQT9378
To Next Page
Loading...
