Audio and video information
About audio from audio output terminals
- - -
Before connecting, read the table below, and confirm the desired audio type and necessary settings ("BD-Video Secondary Audio", "Dolby D/Dolby
o +/Dolby TrueHD" or "DTSIDTS-HD").
(Q
9)
eThe number
of
channels listed
is
the maximum possible number
of
output channels.
HDMI
AV
OUT/DIGITAL AUDIO OUT (CoaxiaIIBD80VOptical)
7.1ch PCM*'
5.1ch PCM
..
: 7.1ch PCM*'
Down-mixed
2ch PCM
DTS Digital
Surround
DTS Digital
Surround/
DTS-ES*6
Down-mixed
2ch PCM
Dolby Digital7.1ch PCM
7.1ch PCM
1!mI!I:
5.1ch PCM
Down-mixed
5.1ch
PCM*2
5.1ch
PCM*2
7.1ch PCM
DTS Digital
Surround/
DTS-ES
Dolby Digital
Plus
DTS-HD High
Resolution
Audio
Dolby TrueHD
DTS-HD Master
Audio
DTS Digital
Surround
DTS Digital
Surround/
DTS-ES*6
Down-mixed
5.1ch PCM
AUDIO OUT (Analog)
5.1ch*2 7.1ch
":7.1ch*'
1!mI!I:
5.1
ch
2ch
5.1ch
7.1ch
7.1ch*'
Down-mixed
5.1ch*2
eAlso, depending on the specifications or the settings of the amplifier/receiver, the results
of
the output may vary.
*1
When the connected equipment is not supported with these audio formats, the audio is output as Dolby Digital bitstream, DTS Digital Surround
bitstream or down-mixed 2ch PCM (e.g., TV).
*2
..
: When playing BD-Video without secondary audio or button click sound, the audio is output as the same format as
if
"BD-Video
Secondary Audio" was set to "Off'.
*3
When the connected equipment is not supported with multi channel surround, the audio is output as down-mixed 2ch PCM.
*4
..
: When the connected equipment is supported with
7.1
channel surround, the audio output is amplified from
5.1
ch or
6.1
ch
to
7.1
ch
depending
on
the DTS, Inc. specifications.
*5 With PCM output, Dolby Digital EX becomes PCM audio decoded as Dolby Digital, DTS-ES recorded to DVD-Video becomes PCM audio
decoded as DTS Digital Surround, and DTS-ES recorded to BD-Video becomes PCM audio decoded as DTS-ES.
*6
..
: When "BD-Video Secondary Audio" is set to "On", Dolby Digital EX is output as Dolby Digital and DTS-ES is output as DTS Digital
Surround, however if playing BD-Video without secondary audio or button click sound, the audio is output as the original format.
Enjoying High Sit rate Audio
of
SO-Video
1mB
. - - -
--~-
- -
This unit supports
high
bit rate audio (Dolby Digital
Plus,
Dolby TrueHD, DTS-HD
High
Resolution Audio
and
DTS-HD Master Audio) adopted
in
BD-Video.
In
order to enjoy these audio formats, the following conditions are necessary. (Part shown in the shaded area
of
table given above)
NECESSARY CONNECTIONS
eHDMI
AV
OUT terminal:
(Q
~
e7.1ch AUDIO OUT
terminal~:
(Q
12)/5.1ch AUDIO OUT terminallBD801:
(Q
13)
NECESSARY SETTINGS
(Q
9)
eSet
"BD-Video Secondary Audio" to "Off'.
eHDMI
AV
OUT terminal: Set "Dolby D/Dolby 0 +/Dolby TrueHD" or "DTS/DTS-HD"
to
"Bitstream" or "PCM" .
e7.1ch AUDIO OUT terminaIIBD80I: Set "Analog Audio Output" to "7.1ch".
e5.1ch AUDIO OUT terminal
BD80:
Set "Analog Audio Output" to "2ch (Downmix) + 5.1ch".
oeThe button click sound on the menu and audio with secondary video
in
picture-in-picture mode
(Q
22) is not output.
RQT9378
To Next Page
Loading...
