Changing
the
speaker
setting
to
suit
your
speakers
B080
When connecting to
an
amplifier/receiver to enjoy multi-channel surround sound, use the following settings on this unit if they cannot be set on the
amplifier/receiver.
The
settings
are
effective
when
connecting
to
analog
7.1ch/5.1ch
AUDIO
OUT
terminal.
Center
(C)
Difference
Setting
Approx. 34 cm
(1
ft.
1 in.) 1.0 ms
Approx. 68 cm (2
ft.
2 in.) 2.0 ms
Approx. 102 cm (3
ft.
4 in.) 3.0 ms
Approx. 136 cm (4
ft.
5 in.)
4.0 ms
Approx. 170 cm (5 ft. 6 in.) 5.0 ms
Circle
of
constant primary listening distance
Q :Actual speaker position
• : Ideal speaker position
® ® © :Primary listening distance
®
Center
speaker
©
Surround/Surround
back
speakers
5.1ch
speaker
connection
7.1ch
speaker
connection
Approximate room dimensions
Difference
Setting
Approx. 170
em
(5 ft. 6 in.) 5.0
ms
Approx. 340 em
(11
ft.
1 in.)
10.0 ms
Approx. 510 em (16 ft. 8 in.) 15.0 ms
Channel balance
(~)
o Select "Test" and press [OK).
A test signal
is
output.
Front
(L)~Center
(C)~Front
(R)~Surround
(RS)
t t
Surround
(LS)--
Surround Back (LB)
__
Surround Back (RB)
e While listening to the test signal, press [A.
~]
to adjust the
volume
of
each speaker
Front speakers: 0.0 to
-6.0
dB
Center and surround speakers: 0.0 to
-12.0
dB
e Press [OK).
The test signal stops.
-No
signal is output for the subwoofer.
To
adjust its volume. play
something. then return to this screen to adjust to suit your taste.
Subwoofer
(SW)
(LB)
Surround
back(RB)*
D
(LS)
Surround
(RS)
Front
(L)
Complete
Test
----,.s-c.c.:o,
Large
-Large:
-Small:
~
Small
No
Select when the speaker supports low-frequency
(under 100 Hz) reproduction.
Select when the speaker does
not
support
low-frequency reproduction.
In order to
make
an ideal listening environment. settings
of
speaker
sizes
may
be automatically adjusted.
For example. if the subwoofer
is
set to "No". the front speakers will
automatically be set to "Large". (In this case. we recommend
connecting a speaker that can reproduce bass below 100 Hz.)
Preparation
o Set "Analog Audio Output" to "2ch (Downmix) +
5.1
ch" or "7.1 ch".
(~
34)
A message is displayed.
e Press [OK).
* Surround back channel is enabled only when setting "Analog Audio
Output" to "7.1 ch".
Speaker presence and size (
~W!E~~~~
)
Set all the connected speakers individually.
o Press
[A,
~
.....
~)
to select the speaker icon and press [OK).
e Press [A.
~)
to select the setting and press [OK).
Icon
examples:
Surround speaker (LS)
Delay time (Iil)
For optimum listening with 7.1/5.1-channel sound. all the speakers,
except for the subwoofer. should be the same distance from the
seating position.
If you have to place the center, surround and surround back speakers
closer to the seating position. adjust the delay time to make up for the
difference.
If either distance
® or © is less than ®
(~
right). find the difference
in the relevant table and change to the recommended setting.
o Press [A.
~
.....
~)
to select the delay time box (
iii)
and press
[OK).
e Press
[A.
~)
to select the setting and press [OK].
To
finish
the speaker setting
Press
[A,
~
.....
~)
to select ·Complete" and press [OK).
RQT9378
To Next Page
Loading...
