PageOn the
unit's
display
j
'--F-9-9-----------
re
--T--h--e
-~-nit-f~I~-t;-;;;~~-i-;prop;~iY.P;e-s-sTpoWER-C)-1
I-I]-;~the
rn~I~-un
--I-t'
-t--o--'s-'w"-itch
I
the unit to standby for 3 seconds. Now press [POWER
<.!.JIll
on the main unit
I I
again to turn the unit
on_
I .
f------------+------------------------t----~
f-H_D_M_I_O_N_L_Y
-+_e_S_o_m_e_B_D_-_V_id_e_o_d_i_Sc_s_c_a_n_o_n_IY_be_o_ut_p_u_t
w_ith_H_D_M_'_.
~
-_~
NET eDisplays while VIERA CAST is starting up. I - ,
I
.~
No
PLAY eThere is a viewing restriction on a BD-Video or DVD-Video. i
32
:
I------------+--------------------.----------i-------j
No
READ
eThe media is dirty or badly scratched. The unit cannot play. ! - I
PLEASE
WAIT eThe unit is carrying out internal process. This
is
not a malfunction.
You
cannot
II
-
II
operate the unit while "PLEASE WAIT" is displayed.
'--
-+_e_W_he_n_co_n_n_e_c_te_d_to_T_V_(_V_'_E_R_A_J_W_it_h_H_D_A_V_'
c_o_n_t_ro_I_4_,_a_nd_
p
_o_w_e_r_su_
p
_
P
_,y_i_s_t_u_rn_e_d_1
-19
ij,
.- off by the "Auto power stand-by" function on the TV side.
...
REMOVE eThe USB device is drawing too much power. Remove the USB device.
SET D eThe remote control and main unit are using different codes. Change the code on 36
("
D "
stands
for
a
number.)
the remote control.
Press and hold [OK] and the indicated number button at the
same time for more than 5 seconds.
UNFORMAT
eYou inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL
or
DVD-RW (DVD-Video formatJ.
UNSUPPORT e
You
have inserted a media the unit cannot play.
eYou tried to operate with a non-compatible USB device.
6, 7
7
U59
eThe
unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until
the message disappears.
Select a position with good ventilation when installing the unit. Do not block the
cooling fan on the rear
of
the unit.
U72
U73
eThe HDMI connection acts unusually.
-The
connected equipment is not HDM' compatible.
-Please
use HDMI cables that have the
HDMIIogo
(as shown on the coverJ.
-The
HDMI cable is damaged.
HDDor
FDD
eThere is something unusual. (The service number displayed after
Hand
F
depends on the unit's condition.J
eCheck
the unit using the troubleshooting guide. If the service number does not
disappear, do the following.
1 Disconnect the plug from the AC outlet, wait a few seconds, then reconnect
it.
2 Press [POWER
<.!.J/I]
to turn the power on. (The unit may be fixed.J
If the service number does not disappear despite doing the above, request
service from the dealer. Inform the dealer
of
the service number when requesting
service.
42-44
START
eThe
system is being restarted during the firmware update. Please do not turn off
power.
16
UPDD/D
eThe
firmware is being updated.
16
FINISH eThe firmware update is complete.
16
41
ROT9378
To Next Page
Loading...
