RQTC0147
6
STEP 1 Connection
≥Select “Off” in “Audio Output” (➜ 16, “HDMI” menu).
Turn on the TV and select the appropriate video input on the TV.
To change these settings later
Select “QUICK SETUP” (➜ 16, “Others” menu).
Point the remote control at the TV.
1 While pressing [Í TV], enter the code with the numbered buttons.
Input a remote control code number referring to the table on the back cover.
e.g., 0001: [0] ➜ [0] ➜ [0] ➜ [1]
≥If your TV brand has more than one code listed, select the one that allows correct operation.
≥If your TV brand is not listed or if the code listed for your TV does not allow control of your TV, this remote control is not
compatible with your TV. Use the TV’s remote control.
2 Test by turning on the TV and changing channels.
Enjoying multi-channel surround sound
STEP 2 The remote control
∫ Batteries
≥Insert so the poles (i and j) match those in the
remote control.
≥Do not use rechargeable type batteries.
Do not:
≥mix old and new batteries.
≥use different types at the same time.
≥heat or expose to flame.
≥take apart or short circuit.
≥attempt to recharge alkaline or manganese batteries.
≥
use batteries if the covering has been peeled off.
Mishandling of batteries can cause electrolyte
leakage which can damage items the fluid contacts
and may cause a fire.
Remove if the remote control is not going to be used
for a long period of time. Store in a cool, dark place.
∫ Use
Aim at the remote control signal sensor (➜ 7),
avoiding obstacles, at a maximum range of 7 m (23
feet) directly in front of the unit.
STEP 3 QUICK SETUP
12 3 4 5
Power on.
Shows QUICK
SETUP screen.
Follow the message
and make the settings.
Press to finish
QUICK SETUP.
Press to
exit.
STEP 4 TV operation
(You can use this unit’s remote control to operate your TV.)
OPTICAL
COAXIAL
DIGITAL AUDIO OUT
(PCM/BITSTREAM)
5. 1
CENTER
SUBWOOFER
COAXIAL IN
CENTER SUBWOOFER
SURROUND
(L) (R)
FRONT
(L) (R)
COAXIAL IN OPTICAL IN
OPTICAL
AUDIO OUT
5. 1c h
2ch
L
L
R
R
CENTER
SURROUND
FRONT L/L
SUBWOOFER
FRONT R/R
Coaxial
cable
Audio cable
Connect cables to
terminals corresponding to
the speakers you have
connected.
≥Change “Speaker
Settings” (➜ 16,
“Audio” menu and
page 17, Changing
the speaker setting
to suit your
speakers).
WITH AUDIO IN 5.1ch
≥Change “PCM Digital Output”, “Dolby
Digital” and “DTS Digital Surround”
(➜ 16, “Audio” menu).
To obtain maximum performance of DVD-Audio multi-channel
PCM sound, this connection is recommended.
Amplifier with a built-in
decoder or a decoder-
amplifier combination
≥You cannot use DTS Digital Surround decoders
not suited to DVD.
≥Even if using this connection, output will be only
2 channels when playing DVD-Audio.
To enjoy multi-channel surround sound, connect
with 5.1 ch AUDIO OUT terminals (
➜
right) or
HDMI terminals (➜ 5).
Optical digital audio cable
Do not bend sharply when connecting.
WITH COAXIAL IN or OPTICAL IN
Amplifier
Back of the unit
or
R6/LR6, AA
SETUP
RETURN
ENTER
SETUP
Connection/The remote control/QUICK SETUP/TV operation
6
RQTC0147-12.fm Page 6 Monday, July 23, 2007 6:13 PM
To Next Page
Loading...
