In the heating mode running for 30 seconds above, press the
button to stop the heater. The fan will stop running after a delay
of 10 seconds.
Heater may stop heating when temperature in bathroom is up to required degree,
and may restart heating as the temperature in bathroom cools down.
2.
1.
Hot startup function: After the product starts up in the heating mode when the
temperature in the bathroom is lower than 20 °C, it enters the hot startup status to
avoid blowing of cold air, and the fan runs at a low speed. When the temperature in
the bathroom reaches 20 °C or above or after running for 60 seconds, the hot startup
status stops and the fan runs at a high speed.
1
2
3
在沐浴前開舒適暖氣功能，可提前把浴室加溫。
按 按鈕，溫暖沐浴模式以暖氣強檔開始運轉。運轉至所設時間後自動
進入換氣強檔模式，運轉三分鐘後自動進入換氣弱檔模式並連續運轉。
運轉過程中，可通過 調整設置時間。
（暖氣結束後，進入換氣狀態，時間不可調。）
運轉過程中，可通過 按鈕，調整上下風向。
（暖氣結束後，進入換氣狀態，風向不可調。）
當浴室內溫度上升到一定程度時，加熱器停止工作，待溫度下降到一定程度後，加熱器重新開始
工作。
如需在運轉途中停止，請按 按鈕。
熱啟動功能：當浴室溫度低於20 °C時，以暖氣模式啟動後，為避免冷風吹出，產品進入熱啟動
狀態，扇葉以低速運轉，待浴室溫度達至20 °C以上或經過60秒 後 ， 熱 啟 動 狀 態 停 止 ， 扇 葉 以
高速運轉。
若在暖氣模式運轉30秒以上，按 按鈕後，為使加熱器冷卻，
扇葉將延遲10秒停止運轉。
Before taking a bath, start the heating function to warm the
bathroom beforehand.
Press the button to start the heating mode at the HI.It will
switch to the VENT. mode at the HI. automatically when the set
time is up. After 3 minutes. ,it will switch to the VENT. mode at the
LO. automatically and run continuously.
During running, you can press to change the set time.
(After heating , enter the ventilation state, the time is
not adjustable.)
To stop midway in running,pressthe button.
During operation, you can press the button to adjust up and
down wing direction.(After heating , enter the ventilation state
and the wind direction is not adjustable.)
20
貼心模式 - 溫暖沐浴功能的使用方法
CARE MODE - HOW TO USE WARM BATH FUNCTION
4
暖氣 強檔
HEAT(HI.)
換氣 強檔
VENT.(HI.)
換氣 弱檔
VENT.(LO.)
(Initial settings)
(初始 設置)
遙控器不 顯 示 此 狀 態 時 間
The remote does not
display this status time
(15分 鐘) (3分 鐘) (持續)
(15 minutes) (3 minutes) (continued)
Use when you feel cold in a bath
在浴室中感到冷時使用
To Next Page