Panasonic HC-X2000 - Screen status display

Chapter 7 Output and Screen Display — Screen status display
- 159 -
Screen status display
Screen display during shooting
*1 Displayed when using .
*2 The tally lamp is available when the handle unit ( supplied, optional) is attached.
1 Time code
Each time you press the USER button assigned to [COUNTER] or touch the USER button icon, the next display is shown or it switches to no display.
≥ [TCG **:**:**:**]: Displays the time code. [TCR **:**:**:**] will be displayed during playback.
≥ [UBG ** ** ** **]:Displays the user bits. [UBR ** ** ** **] will be displayed during playback.
≥ [CLIP *:**:**:**]: Displays the counter value of each clip. This is displayed when the [RECORDING] menu → [REC COUNTER] is set to
[CLIP]. Displays the counter value of the clip being played back during playback.
≥ [*:**:**:**]: Displays the cumulative counter value from the reset position. This is displayed when the [RECORDING] menu → [REC
COUNTER] → [TOTAL] is set.
2 Frame rate
≥ [S.SLOW120]: Displayed when set to the [SYSTEM] menu → [SUPER SLOW] → [ON] and the [SYSTEM] menu → [FREQUENCY] → [59.94Hz].
≥ [S.SLOW100]: Displayed when set to the [SYSTEM] menu → [SUPER SLOW] → [ON] and the [SYSTEM] menu → [FREQUENCY] → [50.00Hz].
≥ (No display): It is not displayed when set to the [SYSTEM] menu → [SUPER SLOW] → [OFF].
3 <AUTO/MANU> switch
Displayed when the <AUTO/MANU> switch is set to <AUTO>.
4 Message display area for stop of cooling fan
Displays a message when the cooling fan has stopped.
5 Recording status
Displays the recording status of the memory card in card slot 1 or card slot 2.
≥ , : Not target for recording.
≥ (flashing), (flashing): Recognizing the memory card.
≥ , : The recording is stopped while the recording target memory card is inserted.
≥ , : Recording.
≥ (Flashing red dot), (Flashing red dot): Processing to stop the recording.
≥ [P ], [P ]: Recording is stopped with pre-recording is enabled and the recording target memory card is inserted.
≥ (No display): It is in one of the following conditions.
j A memory card has not been inserted.
j The memory card cannot be recognized.
The following indicators are displayed in card slot 1 only.
≥ [P]:Pre-recording is enabled, and the memory card is not inserted in the card slot, or the memory card is not recognized.
≥ : The tally lamp is instructed to illuminate in red via network.
*2
≥ : The tally lamp is instructed to illuminate in green via network while the recording is stopped.
The tally lamp on the handle unit does not illuminate green.
*2
TCG 1 2 : 3 4 : 5 6 : 2 8
2160-59.94p
MOV HEVC 200M
A001C001
Ach
IP REMOTE
30dB ND:CLR 1/8000 F5.6
+1.0EVDEC 3 1 2 0 2 0 1 0 : 4 5 : 3 0
iZ50
MF99
D2x
IR
70%
HDMI INTRVL
ND1/16
FLUO
999min 999min
S.SLOW120
FBC
RELAY
DRS
STD
[ + ]
CH1
CH2
ICONS
VOLUME [ - ]
1 2 3 5 6 7 5 6 8 9 10 11
15 16 17 18 19 20 21 22 23 24
38
26
28
30
31
41
42
43
27
25
29
39
40
30
44
45
32
33
34
35
36
37
4 12
13 14
X2000
X2000 X1500