Panasonic LS-400 Series - Page 8

8
Digital Laser Sensor LS-400 SERIES
Designation Model No. Description
Sensor head
mounting
bracket
MS-CX-1
Foot angled mounting bracket
MS-CX-2
Foot biangled mounting bracket
Flat mounting possible to avoid obstructions caused by the height of the sensor.
MS-CX-3
Back angled mounting bracket
MS-CX-4
Protective mounting bracket
Protects sensors preventing beam axis displacement due to shocks.
Sensor mounting
bracket for beam
axis alignment
MS-CX-11
Mounting bracket that makes ne beam axis alignment possible
after setting the sensor head.
Adjustment angle: up and down, right and left: 4 degrees
Mounting directions: two directions, vertical and horizontal
Universal sensor
mounting stand
MS-AJ1
Horizontal mounting type
Basic assembly
MS-AJ2
Vertical mounting type
MS-AJ1-A
Horizontal mounting type
Lateral arm assembly
MS-AJ2-A
Vertical mounting type
Amplier mounting bracket
MS-DIN-2
Mounting bracket for amplier
Reector mounting bracket
MS-RF23
Mounting bracket for RF-230
Amplier
protection seal
FX-MB1
10 sets of 2 communication window seals and 1 connector seal
Communication window seal: It prevents malfunction due to transmission signal from another
amplier, as well as, prevents effect on another amplier.
Connector seal: It prevents contact of any metal, etc., with the pins
of the quick-connection cable.
Reector
RF-310
For coaxial retroreective type
Compact reector
Sensing range (U-LG mode)
• LS-H91(F): 0.1 to 7 m
0.328 to 22.966 ft
•
LS-H91(F)-A: 0.1 to 5 m
0.328 to 16.404 ft
Reective tape
RF-33
For coaxial retroreective type
Size: 25.2 × 27.8 × t 0.4 mm
0.992 × 1.094 × t 0.016 in
RF-31
For coaxial retroreective type
Size: 9.2 × 9.2 × t 0.4 mm
0.362 × 0.362 × t 0.016 in
Bank
selection unit
FX-CH
NPN input type
Setting for up to 16 laser sensors can be
changed at once by means of external signals.
FX-CH-P
PNP input type
Sensor head mounting bracket
• MS-CX-1 • MS-CX-2
Two M3 (length 12 mm
0.472 in
) screws with
washers are attached.
Tw
o M3 (length 12 mm
0.472 in) screws with
washers are attached.
Universal sensor mounting stand
45°
45°
Elevation
angle: ±45°
Swivel:
360° rotation
Mounting hole
for M6 screw
Height
adjustment:
150 mm
5.906 in
approx.
• MS-AJ1 • MS-AJ1-A
45°
45°
Angle
adjustment:
±45°
Swivel:
360°
rotation
Mounting hole
for M6 screw
360
°
With the lateral arm,
the sensor can
sense from above
a production line.
Forward / back
adjustment
130 mm
5.118 in
approx.
Height
adjustment:
150 mm
5.906 in
approx.
• MS-AJ2
45°
45°
Elevation
angle:
±45°
Mounting hole
for M6 screw
Height
adjustment:
150 mm
5.906 in
approx.
Swivel:
360° rotation
• MS-AJ2-A
360
°
45°
45°
Angle
adjustment:
±45°
With the lateral arm,
the sensor can
sense from above a
production line.
Swivel:
360° rotation
Mounting hole
for M6 screw
Forward / back
adjustment
130 mm
5.118 in
approx.
Height
adjustment:
150 mm
5.906 in
approx.
Reector
• RF-310
24 mm
0.945 in
12 mm
0.472 in
4 mm
0.157 in
Reective tape
• RF-33
27.8 mm
1.094 in
0.4 mm
0.016 in
25.2 mm
0.992 in
• RF-31
9.2 mm
0.362 in
0.4 mm
0.016 in
9.2 mm
0.362 in
OPTIONS
• MS-CX-3 • MS-CX-4
Two M3 (length 12 mm
0.472 in
) screws with
washers are attached.
Two M3 (length 12 mm
0.472 in
) screws with
washers are attached.
Sensor mounting bracket
for beam axis alignment
Amplier mounting bracket
• MS-DIN-2
Reector mounting bracket
• MS-RF23
Two M4 (length 10 mm 0.394 in)
screws with washers are attached.
Amplier protection seal
• FX-MB1
Communication
window seal
Connector seal
• MS-CX-11
Two M3 (length 14 mm
0.551 in) screws with
washers are attached.
Bank selection unit
• FX-CH(-P)