32
TITLE ITEMS
"T1
<ii"
,,,
:::,-
m
X
-u
0
(/)
C
;a
m
0
)>
-u
-I
C
~
z
G)
0
0
r
0
C
;a
;a
m
-u
;a
0
0
C
0
-I
0
z
-u
0
~
m
;a
0
ci'i
-u
~
Colour
is
strange when the Flash
is
fired.
The appearance of the light source
is
strange.
(The light source appears ahead the
subject.)
The Exposure condition can not
be
changed
Although [ AF/AE
LOCK]
button is pressed,
only focus is locked.
(A
E
is
not locked)
The pictures recorded with
[ AUTO
BRACKET]
function are
too dark/bright.
The Exposure condition
is
changed
extremely.
Although shutter is released,
no picture
is
captured.
[ AUTO
BRACKET]
does not work.
Colour
is
strange.
Colour
is
strange. (With Flash)
The colour
is
strange
(On
PC
monitor/ Printout image
.)
The Power
is
turned off.
Abnormal Picture Effect.
Certain part of the picture is
flashing
in
Black & White.
Firmware version
DESCRIPTION
*The colour of the subject which is other than Flash reachable distance
is
not coverage of white balance.
*Confirm that [ WB Adjustment ) setting condition.
(Press the cursor
[RIGHT)
(WB) button, then press the
cursor [DOWN]button,
in
order to execute the
[ WB Adjust. ] screen.
*It also effects to the Flash recording mode as well.
*Normally, the light source appears ahead the subject.
(This
is
the effect of the 1 st curtain synchro.)
< 1
st
Curtain
Sync
>
*Focus & Exposure condition
is
locked when the [ AF / AE
Lock)
button.
⇒
[ CUSTOM
MENU]
(1/6) ----- [ AF/AE
Lock]
(AE LOCK,
AF
LOCK, AF/AE LOCK, AF-ON)
*It can be reset when [ AF / AE
Lock]
button
is
pressed again.
*
By
assigning [ AF/AE
LOCK]
to
[ Q.MENU/Fn1 ] or [
Fn2]
button, [ AF/AE
LOCK]
button will
be available.
⇒
[ CUSTOM
MENU)
(4/6) ----- [
Fn
Button Set )(Fn1 , Fn2) ----- [ AF/AE
LOCK)
*Focus does not hold even if [ AF/AE
Lock]
button
is
pressed if the [ AF/AE
Lock]
is
set to [ AF I
⇒
[ CUSTOM
MENU)
(1/6) ----- [ AF/AE
Lock)
(AE LOCK,
AF
LOCK, AF/AE LOCK, AF-ON)
*AF Lock only
is
effective when taking pictures
in
Manual Exposure Mode.
*
In
the Manual Focus condition, It
is
only worked as [ AE
lock]
function, regardless any settings.
*The [ Auto Bracket]
is
selected after setting the [ EXPOSURE COMPENSATION],
the compensated value is effected for its reference value.
*Spot metering mode
is
the method
to
measure the subject
in
the
spot metering target.
*Confirm the setting condition of [ EXPOSURE COMPENSATION]
(1/3 EV Step, -3EV
to
+3EV)
uJ
Spot
metering target
*Although the shutter button
is
fully pressed, it can not take a picture until the subject
is
not focused.
(It is able to take a picture when the Focus Priority turns [ OFF ] although focus condition does
not perfect.) OFF
is
gives priority to the best time to take a picture.
⇒
[ CUSTOM MENU ] (2/6) ----- [ Focus/Release Priority ](FOCUS, RELEASE)
*Only single picture
is
able
to
captured when flash is fired.
*Auto Bracket
is
disabled
in
the following cases.
- [ Glistening Water)/[ Glittering Illuminations)/[ Soft Image of a Flower) (Scene Guide Mode)
- [ Miniature Effect]/[ Soft
Focus]/[
Star Filter]/[ Sunshine] (Creative Control Mode)
- In Self Portrait Mode.
- When White Balance Bracket
is
set.
- When recording motion pictures
- When recording using the flash
- When [ HOR ] is set to [
ON
]
- In [ Stop Motion Animation) (only when [ Auto Shooting]
is
set)
*The exposure may not be compensated with auto bracket depending on the brightness of the subject.
*There
is
a possibility that [ Finely adjusting the white balance] is
selected/shifted.
*Confirm that [ WB Adjustment ) setting condition.
(Press the cursor
[RIGHT]
(WB) button, then press the
cursor [ DOWN ] button,
in
order to execute the [ WB Adjust. ) screen.)
*It
is
resumed/memorized although power turns off/on.
*The flash light does not reach enough to the subject due to the over than flash reachable
distance.
In
this case, white balance may be other than its coverage.
*There
is
a possibility that the picture
is
captured with [ AdobeRGB ) setting
⇒
[REG]
(5/6) ----- [ Color
Space)
(sRGB, AdobeRGB)
*To proceed proper colour reproduction for AdobeRGB, the AdobeRGB capable PC and Printer
are necessary.
*
In
accordance with PC environment, it may not
be
displayed properly when the picture
is
re-sized
with business software.
*Confirm that the setting condition of [ Sleep Mode ).
(If the camera has not been used for the time selected
on
the setting, the power turns off automatically.)
⇒
[
SETUP]
(2/5)-
----
[Economy]
[ Sleep
Mode]
(10MIN
.,
5 MIN
.,
2 MIN
.,
1 MIN
.,
OFF)
*Confirm that the setting condition of [ Highlight].
⇒
[ CUSTOM
MENU]
(3/6) -----
[Highlight]
(O
N, OFF)
The white saturated areas appear blinking
in
Black and White.
*Confirm that the firmware versions of the body and lens to
be
checked.
⇒
[ SETUP ] (4/5) ----- [ Version Disp. ]
To Next Page
Loading...
