Panasonic Omnivision PV-V4020 User Manual

‘Important: If the remote control POWER, ACTION, PROGA/CR+, CHA/v, NUMBERED keys,
INPUT, SEARCH or ADD/DLT button does not work when pressed, press the VCR
button on the remote and try the button again.
CHANNEL/CLXK AUTO SET
Start Channel Auto Set
and Clock Auto Set.
IMPORTANT NOTE FOR
AUTO CLOCK SET
CONNECT ANTENNA CABLE
AND IF YOU USE A CABLE
BOX,TUNE IT TO YOUR
LOCAL PBS CH THEN, . .
PLEASE PUSH CH UP KEY
Press CH ▲ .
CH AUTO SET PROCEEDING
AUTO CLOCK SET
PROCEED ING
Case1
^ (Setup completed)
1/ 4/2000 TUE 12:00PM
DST;ON
SETTING : CH 02
AUTO CLOCK SET
COMPLETED
END : PUSH CH UP KEY
Press CH A
to exit.
If your area observes DST (daylight
saving time), but the time is incorrect;
do the ‘Time Zone Adjust” steps on page 29.
EJECT LIGHT
(v^ (Tv) (^)
a v^J
.el
SELECT/
SET
▲ :PLAY
- ▼ :STOP
◄ :REW
► :FF
rn (T3 (T)
CID GD GD
(T^ ra~”t
ACTION
GD GX)
OOATW RESET QiSPLAY f/VPl PQSlTlQM
O r i CD
PAUSE CM SKIP SPEED SEARCH.
CD O O O-i
SLOW , -—
CD ©I-
SAFVHi-FI VOL CH ^ REC
Model PV-V4520 remote is shown here.
• Auto clock set is perfomned the
first time the VCR is turned off
each day. If used, a cable box
must be left on and tuned to the
PBS channel at the time VCR
power is turned off if you want auto
clock set to be done.
• If used, a DSS receiver must be
turned off for auto clock set.
• If Cable Box or DSS receiver is
connected to VCR via Audio/Video
jacks, an RF coaxial cable must
also be connected for auto clock
set and channel auto set features
to work.
AUTO CLOCK SET
(Setup incomplete)
- Clock Setup incomplete.
Set the clock manually.
^ \^) Press ACTION.
IS INCOMPLETE
PUSH ACTION TO SET CLOCK
SET CLOCK
2) Press AT to
select month.
3) Press ► to set.
SELECT:A ▼ KEY
SET : ► KEY
END :ACT I ON KEY
^^^SETCIjOCK^^^^
DST:ON
• Likewise, set date, year, time,
DST (Daylight Saving Time).
To Make Corrections,
repeatedly press ◄ ► to move to
error, then correct.
SET : ■ < ► KEY
START :ACT ION KEY
4) Press ACTION.
(Clock starts.)
• To exit this
mode, press
ACTION again.
VCR calendar is accurately maintained to
Dec. 31, 2096 11:59PM.
Channel auto set selects normal TV or Cable
channels depending on your VCR hookup.
To reset Language, Channels, Clock or
VCR’s Output Channel see pages 28 and 29.
Using AWM ► keys
You can also operate the menu
screen using VCR buttons.
When menu screens are
displayed, the PLAY, STOP,
REWIND, and FF buttons on "
the VCR and remote function
as AWM ► only with no tape
inserted. _
To exit the menu, repeat above
with or without tape inserted.
To display menu using VCR
buttons, press CH A and CH
T together.
A : PLAY ◄ : REW
T : STOP ► : FF
7
One
Time
VCR
Setup

Panasonic Omnivision PV-V4020 Specifications

General

Brand	Panasonic
Model	Omnivision PV-V4020
Category	VCR
Language	English