Panasonic Omnivision PV-V4020 User Manual

Timer Recording
You can set up to 8 programs to be recorded while you are away.
Display SET PROGRAM.
Press PROGA/CR+.*
Or to display Program screen from the Menu.
1) Press ACTION to display Menu.
2) Press AT and ► to select and set SET UP FEATURE.
3) Press ► to display Program screen.
4) Go to step 3.
• You may also use VCR buttons. See the bottom right.
Check list before you begin.
Q All connections are made.
(See pages 4-5.)
[H TV and VCR are plugged in and turned on.
E] VCR/TV selector is set to “VCR."
□ Clock is set to correct time.
D Record tab in place, (See page 30.)
Q Remote in VCR mode.
2
SET PROGRAM
VCR Plus+ PROGRAMMING
TIMER PROGRAMMING
SELECT:A ▼ KEY
SET : ► KEY
END :PR0G KEY
Display Program screen.
1) Press AT to select
TIMER PROGRAMMING
2) Press ► to display.
• If a program is already in
memory, press AT and
EJECT LIGHT - -
WrW®!
& (E) ®
A
You cannot use the VCR buttons
when on “SET PROGRAM" screen.
► to select an unused
program number.
3
I/ START STOP CH
rODAYN
SLP
SELECT START DATE
SELECT: A T KEY
SET : ► KEY
END ;PROG/ACT I ON KEY
Set the recording DATE.
1) Press AT to select.
2) Press ► or ◄ to set.
5 POWER
SELECT/
i SET
■ A;PLAY
^ T:STOP
4 ◄ i R E W
► :FF
Example p8—9. 31 — 1 —2 . 6
T oday— 7 select A / T Selection Order
L WEEKLY. WEEKLY WEEKLY J
(SAT) ■■■ ■ (MON) (SUN)
• 1 -31 = One time
• DAILY = MON-FRI
• WEEKLY = Same time once
a Week
Repeat step 3 to set:
nJy start time, stop time Channel
(or LINE for outside source),
tape speed (SP, LP, SLP).
QD
GD GSi^QD
CD CD
CD CD CSD
COuNTGnnur OSFVAy T«P( POSJTIM
O CUD O
wuse Cttsiop s«n) nmcH,
GD O O 0-1
SLOW
e
QD GDI
VOL CH I
O (Di
P DT START STOP CH SPD
[1 8 10:00P 12:00P 02 SP|
2
3
4
CANCEL:ADD/DLT KEY
SELECT 1-8: A T KEY
ENTER ; ► KEY
END :PR0G/ACTI0N KEY
End the program.
1) Press PROGA/CR+
(or ACTION).
To Enter More Programs
Press AT to select, and ► to display
a blank program number. Then repeat
step 3.
2) Press PROGA/CR-p
(or ACTION) again to
exit.
\ 1
y
- TIMER -
/ 1
Multi Function Display
Set the timer.
Press POWER off.
• When recording
programs via a cable
box, make sure the
cable box is left ON
and tuned to the
desired channel.
Model PV-V4520 remote Is shown here.
Timer Recording Using VCR
Buttons.
— Using ATM ► keys-
You can also operate the menu screen
using VCR buttons. ,
When menu screens are displayed, the
PLAY, STOP, REWIND, and FF buttons on
the VCR and remote function as ATM ►
only with no tape inserted.
To exit the menu, repeal above with or
without tape inserted,
A : PLAY
T:STOP
◄ : REW
► :FF
To diMlay menu using VCR buttons,
press CH A and CH T together.
On Remote
On VCR

Panasonic Omnivision PV-V4020 Specifications

General

Brand	Panasonic
Model	Omnivision PV-V4020
Category	VCR
Language	English