To Next PageTo Next PageHow to troubleshoot no audio on a Panasonic PT-EW730Z?
If you're not getting any audio output from your Panasonic Projector, check the following: * Ensure the external device is connected correctly to the audio input terminal. * Verify that [MUTE] in [AUDIO SETTING] is not set to [ON]. * Confirm that the audio input selection in [AUDIO SETTING] is set correctly.
Why does video from an HDMI compatible device not appear or appear jumbled on my Panasonic Projector?
If video from an HDMI compatible device doesn't appear or appears jumbled on your Panasonic Projector: * Ensure the HDMI cable is securely connected. * Try turning off and on the power of both the projector and the external device. * Verify that the input signal is compatible with the projector.
Why does the image from my computer not appear on my Panasonic PT-EW730Z?
If you're not seeing an image from your computer on the Panasonic Projector, consider these points: * Check if the cable is too long. (For D-Sub cables, it should be 10 m (32'10") or shorter). * Verify that the external video output on the laptop is set correctly. (For example, you might need to press “Fn” + “F3” or “Fn” + “F10” simultaneously. Refer to your computer's user manual as the method varies.)
Why does my Panasonic Projector shut down with a fan error?
Your Panasonic Projector may be shutting down due to a fan operation error for several reasons. There might be a blown fuse, which would require checking and replacing the power supply block fuse with one rated at 10A. A blown thermal fuse could also be the cause, necessitating its replacement and a check of the usage environment. Additionally, a failure on the signal processing part or a main microprocessor writing error could lead to this issue, requiring checks for FPGA initializing or communication errors and investigation of main software activation errors, respectively.
What to do if the DIGITAL LINK input image or sound is not output on my Panasonic PT-EW730Z?
If the DIGITAL LINK input image or sound is not being output on your Panasonic Projector, check these: * Ensure the connections between the twisted-pair-cable transmitter and the projector or external device are correctly made. * Verify that [DIGITAL LINK MODE] is set to [AUTO] or [DIGITAL LINK], and not [ETHERNET]. * Confirm the input signal is compatible with the twisted-pair-cable transmitter.
What to do if my Panasonic Projector lamp cover is not installed securely?
If your Panasonic Projector is experiencing issues and the lamp cover is not installed securely, ensure that the lamp cover is properly and securely installed.
Why is there no image from DisplayPort on my Panasonic PT-EW730Z?
If the image output from the DisplayPort of your computer does not appear on the Panasonic Projector: * If connecting the projector to a computer that uses an early-type chipset or graphics card compatible with DisplayPort, the projector or computer may not be operated properly. * Consider updating the graphics accelerator driver of the computer to the latest version. * Try turning off and on the power of both the projector and the external device. * Verify that a compatible signal is being input to the projector.
Why don't the buttons on my Panasonic PT-EW730Z control panel work?
If the buttons on the control panel of your Panasonic Projector are not operating, check the following: * Ensure that the [CONTROL PANEL] setting in [CONTROL DEVICE SETUP] is not set to [DISABLE]. * Verify if the terminal is being used for contact control.
Why is my Panasonic Projector not displaying image from computer?
If the image from a computer is not appearing on your Panasonic Projector, consider these points: * Check if the cable is too long. For D-Sub cables, the length should be 10 m (32'10") or shorter. * Verify the external video output on the laptop is set correctly. (For example, the external output settings may be switched by pressing “Fn” + “F3” or “Fn” + “F10” simultaneously. The method varies depending on the computer type, so refer to the user manual provided with your computer.)
What causes a Panasonic Projector image to display incorrectly?
If the image on your Panasonic Projector is not displaying correctly, consider the following: * Ensure the [SYSTEM SELECTOR] selection is set correctly. * Check for any problems with the video tape or other image sources. * Verify that the input signal is compatible with the projector.
General| Matrix size | 0.76 \ |
|---|---|
| Native aspect ratio | 16:10 |
| Projection distance | 1.02 - 10.16 m |
| Vertical scan range | 24 - 120 Hz |
| Horizontal scan range | 15 - 91 kHz |
| Projection technology | DLP |
| Contrast ratio (typical) | 5000:1 |
| Screen size compatibility | 40 - 400 \ |
| Projector native resolution | WXGA (1280x800) |
| Keystone correction, vertical | -40 - 40 ° |
| Keystone correction, horizontal | -30 - 30 ° |
| Focal length range | - mm |
| Lamp type | UHM |
| Lamp power | 400 W |
| Lamps quantity | 1 lamp(s) |
| Light source type | Lamp |
| Service life of light source | 3000 h |
| Service life of light source (economic mode) | 4500 h |
| Full HD | No |
| BNC input ports | 5 |
| HDMI connector type | Full-size |
| Serial interface type | RS-232 |
| USB 2.0 ports quantity | 0 |
| Ethernet LAN data rates | 10, 100 Mbit/s |
| Noise level | 37 dB |
| Noise level (economic mode) | 29 dB |
| Dot clock scanning frequency | 162 MHz |
| RMS rated power | 10 W |
| Placement | Desktop, Ceiling |
| Product type | Large venue projector |
| Product color | White |
| Power source | AC |
| AC input voltage | 100 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (standby) | 0.3 W |
| Power consumption (typical) | 575 W |
| Operating temperature (T-T) | 0 - 45 °C |
| Operating relative humidity (H-H) | 10 - 80 % |
Weight and Dimensions| Depth | 385 mm |
|---|---|
| Width | 530 mm |
| Height | 177.8 mm |
| Weight | 9800 g |
Essential safety warnings for electrical shock, fire hazards, and proper product handling.
Notes on intended use, environmental factors, and regulatory compliance information.
Instructions for different installation modes, ceiling mounting, and projector positioning.
Guide to connecting sources, cables, and understanding terminal assignments.
Procedures for power on/off, remote control usage, and basic projector functions.
How to access and use the projector's on-screen menu system for configuration.
Understanding status indicators and procedures for lamp and filter maintenance.
Guide to troubleshooting common problems with power, image, audio, and controls.
