Panasonic PT-F100NT

S PEC F ILE
PT-F100NT
LCD Projector
As of May 2007 < 7 >
Computer data compatibility
This projector accepts up to 91 kHz horizontal scanning frequency and 162 MHz dot clock.
NOTE: Pixel thinning is applied to signals that exceed a dot clock frequency of 110 MHz. The display resolution of this projector is 1,024
x 768 pixels. If the display resolution indicated in the above data exceeds this resolution, image compression will be used to con-
vert the input signal to 1,024 x 768 pixels.
List of compatible signals
Display mode Display
resolution
(dots)
1
Scanning frequency
H
(kHz)
V
(kHz)
Dot clock
frequency
(MHz)
Picture
quality
2
Format
720 x 480i
720 x 576i
720 x 480i
720 x 576i
720 x 480
720 x 576
1,280 x 720
1,920 x 1,080i
640 x 400
640 x 480
800 x 600
832 x 624
1,024 x 768
1,280 x 768
1,280 x 800
1,152 x 864
1,152 x 870
1,280 x 960
1,280 x 1,024
1,400 x 1,050
1,440 x 900
1,600 x 1,200
15.7
15.6
15.7
15.6
31.5
31.3
45.0
37.5
33.8
28.1
31.5
37.9
31.5
35.0
37.9
37.5
43.3
35.2
37.9
48.1
46.9
53.7
49.7
48.4
56.5
60.0
68.7
47.8
49.7
64.0
67.5
76.7
68.7
60.0
64.0
80.0
91.1
64.0
65.1
55.9
75.0
59.9
50.0
59.9
50.0
59.9
50.0
60.0
50.0
60.0
50.0
70.1
85.1
59.9
66.7
72.8
75.0
85.0
56.3
60.3
72.2
75.0
85.1
74.6
60.1
70.1
75.0
85.0
59.9
59.8
71.2
74.9
85.0
75.1
60.0
60.0
75.0
85.0
60.0
60.0
59.9
60.0
-
-
13.5
13.5
27.0
27.0
74.3
74.3
74.3
74.3
25.2
31.5
25.2
30.2
31.5
31.5
36.0
36.0
40.0
50.0
49.5
56.3
57.3
65.0
75.0
78.8
94.5
79.5
83.5
94.2
108.0
121.5
100.0
108.0
108.0
135.0
157.5
108.0
122.4
106.5
162.0
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
AA
AA
AA
AA
A
A
A
A
A
A
A
A
A
A
A
A
A
A
NTSC/NTSC4.43/PAL-M/PAL60
PAL/PAL-N/SECAM
525i (480i)
625i (576i)
525p (480p)
625p (576p)
750 (720)/60p
750 (720)/50p
1125 (1080)/60i
1125 (1080)/50i
VESA70
VESA85
VGA60
VGA65
VG
A72
VGA75
VGA85
SVGA55
SVGA60
SVGA70
SVGA75
SVGA85
MAC16
XGA60
XGA70
XGA75
XGA85
WXGA768
WXGA800
MXGA70
MXGA75
MXGA85
MAC21
MSXGA60
SXGA60
SXGA75
SXGA85
SXGA60+
WXGA+
UXGA60
VIDEO/S-VIDEO
COMPONENT
(YPBPR only) /
COMPUTER (RGB only)
COMPUTER
1. The “i” appearing after the resolution indicates an interlaced signal.
2. The following symbols are used to indicate picture quality.
AA Maximum picture quality can be obtained.
A Signals are converted by the image processing circuit before picture is projected.