Panasonic PT-RZ660

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 131
8) Press asqw to select [COMMAND].
9) Press the <ENTER> button.
f The [COMMAND] detailed screen is displayed.
10) Press as to select a [COMMAND].
f For [COMMAND] which requires detailed settings, the items of the detailed settings will switch each time
you press qw.
f When [INPUT] is selected, press the <ENTER> button, and then press asqw to select the input to be
set.
[COMMAND]
Detailed settings of
[COMMAND]
Description
[POWER ON] ― Switches on the projector.
[STANDBY] ― Enters standby.
[QUICK STARTUP]
[ON]
Enables the function of the [PROJECTOR SETUP] menu →
[QUICK STARTUP].
[OFF]
Disables the function of the [PROJECTOR SETUP] menu →
[QUICK STARTUP].
[SHUTTER]
[OPEN] Disables the shutter function (shutter: open).
[CLOSE] Enables the shutter function (shutter: closed).
[INPUT]
[RGB1] Switches the input to RGB1.
[RGB2] Switches the input to RGB2.
[DVI-D] Switches the input to DVI-D.
[HDMI] Switches the input to HDMI.
[DIGITAL LINK] Switches the input to DIGITAL LINK.
[SDI]
*1
Switches the input to SDI.
[INPUT1] - [INPUT10]
*2
Switches the input to DIGITAL LINK, and switches the input of the
Panasonic twisted-pair-cable transmitter to the specied input.
[OPERATING MODE]
*3
[NORMAL] Prioritizes luminance.
[ECO]
Controls the power to increase the life of the light source with higher
luminance.
[LONG LIFE1]
Controls the power to increase the life of the light source although
the luminance is lower than that of [ECO].
[LONG LIFE2]
Controls the power to increase the life of the light source although
the luminance is even lower than that of [LONG LIFE1].
[LONG LIFE3]
Controls the power to increase the life of the light source to the
maximum although the luminance is even lower than that of [LONG
LIFE2].
[USER1] Controls the power with the setting set in [USER1].
[USER2] Controls the power with the setting set in [USER2].
[USER3] Controls the power with the setting set in [USER3].
[P IN P]
[OFF] P IN P function is not used.
[USER1] Places the sub screen with the setting set in [USER1].
[USER2] Places the sub screen with the setting set in [USER2].
[USER3] Places the sub screen with the setting set in [USER3].
*1 Only for PT-RZ770, PT-RZ660
*2 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, its input
name is automatically reected from [INPUT1] to [INPUT10]. When an item that does not reect the input name is selected, it will be disabled.
*3 If you change the settings while using the projector, the duration until the luminance of light source decreases by half may shorten or the
luminance may decrease.
11) Press the <ENTER> button.
f The command is xed and n is displayed at the left of the selected command.
f After the command is xed, press the <MENU> button to close the detailed setting screen.
12) Press asqw to select [STORE], and press the <ENTER> button.
Note
f To delete a command that has been already set, press the <DEFAULT> button on the remote control while the screen in Step 5) is
displayed, or select [DELETE] at the screen in Step 6) and press the <ENTER> button.
f If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
f The operating time will be the local time. (x page 129)