Panasonic SA-HE200 - User Manual

Other manuals for Panasonic SA-HE200

Questions and Answers:

B
brenda34Aug 7, 2025
Why is there a lot of noise and interference on my Panasonic Stereo Receiver radio?
- N
  Nicole GonzalezAug 7, 2025
  If you're experiencing a lot of noise and interference when using the radio on your Panasonic Stereo Receiver, consider these solutions: * Connect the appropriate antenna. Consider using an outdoor antenna or one with more elements. * Adjust the position of the FM or AM antenna. * Reduce the treble. * Select 'SOURCE DIRECT'. * Turn off nearby televisions, video decks, DVD players, and satellite receivers. * Separate the antenna from other cables, leads, and appliances. * Change the frequency step. Hold [-BAND, –FM MODE, DISPALY MODE] down for 3 seconds to change the step to 9 kHz.
J
john01Aug 14, 2025
What to do if the correct AM frequency cannot be tuned in on Panasonic SA-HE200 Stereo Receiver?
- R
  Russell MckinneyAug 15, 2025
  If you're unable to tune in the correct AM frequency on your Panasonic Stereo Receiver, try the following: * Connect the appropriate antenna, possibly an outdoor one. * Adjust the position of the FM or AM antenna. * Reduce the treble. * Select 'SOURCE DIRECT'. * Turn off nearby televisions, video decks, DVD players, and satellite receivers. * Separate the antenna from other cables, leads, and appliances. * Change the frequency step by holding [-BAND, –FM MODE, DISPALY MODE] down for 3 seconds to change the step to 9 kHz.
T
tracy65Aug 21, 2025
Why is sound not heard from the center, surround, or subwoofer speakers on my Panasonic SA-HE200 Stereo Receiver?
- M
  Megan JonesAug 21, 2025
  If you're not hearing sound from the center, surround, or subwoofer speakers on your Panasonic Stereo Receiver, check the following: * Ensure the SPEAKERS settings for your speakers are correct. * Check the DSP sound mode. * Turn ENHANCED SURROUND on. * Turn DVD 6CH INPUT off. Also, note that if the input is PCM with sampling frequencies of 96 or 88.2 kHz, the DSP switches to STEREO.
A
Aaron MillerOct 29, 2025
What to do if my Panasonic SA-HE200 has no sound?
- L
  Lisa MartinOct 29, 2025
  If your Panasonic Stereo Receiver has no sound, try the following: * Ensure the AC mains lead is connected. * Turn the volume up. * Check connections to speakers and other equipment. * Turn on the speakers. * Turn off the tape monitor. * Select the correct source. * Change the D-INPUT setting to suit the type of connection you have made. * Check that the digital signals can be decoded by this unit. * Turn PCM FIX or DTS FIX off. * If shorting (bare wires touching) of positive and negative speaker wires, using speakers with an impedance lower than that rated for this unit, straining of the speakers through excessive volume or power, or using the unit in a hot environment without proper ventilation, switch off the unit, determine and correct the cause, then switch the un...

Panasonic SA-HE200 Specifications

Amplifier Section

power output	2 × 100 W (6 Ω)
continuous power output	2 × 80 W (6 Ω)
total harmonic distortion at rated power	0.05 % (6 Ω)
total harmonic distortion at half power	0.03 % (6 Ω)
power bandwidth	10 Hz –100 kHz (6 Ω, 0.9 %)
damping factor	45 (6 Ω)
load impedance front A or B	4–16 Ω
load impedance front A and B	8–16 Ω
load impedance center	6–16 Ω
load impedance surround	6–16 Ω

FM Tuner Section

frequency range	87.50–108.00 MHz
sensitivity S/N 30 dB	1.5 µV/75 Ω
sensitivity S/N 26 dB	1.3 µV/75 Ω
sensitivity S/N 20 dB	1.2 µV/75 Ω
IHF usable sensitivity	1.5 µV/75 Ω
IHF 46 dB stereo quieting sensitivity	22 µV/75 Ω
total harmonic distortion mono	0.2 %
total harmonic distortion stereo	0.3 %
frequency response	20 Hz–15 kHz +1 dB, –2 dB

General

power supply for continental Europe	AC 230 V, 50 Hz
power supply for the United Kingdom	AC 230–240 V, 50 Hz
power consumption	280 W
dimensions	430 × 158 × 377 mm
mass	11.9 kg
power consumption in standby mode	2 W

Video Section